Honda Karcher G2400HH-R Pressure Washer Logo

Related Topics:

Question about Honda Karcher G2400HH-R Pressure Washer

1 Answer

Cant pull start the pressure washer - Honda Karcher G2400HH-R Pressure Washer

Posted by budreau2004 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 23 Answers

Turn water off to the pressure washer, release pressure by applying hand pressure to sprayer. After water pressure is released, turn water back on (should not have motor running without water.) then try to pull start.

Posted on Jun 18, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why is my detergent not working on my new k5 pressure washer

If you are referring to an electric washer,The wand for the detergent is a double action wand. You usually pull the wand end out for low pressure and detergent flow.
May 30, 2014 • Garden
0helpful
1answer

I cant start my power washer. the pull start is locked and wont release to start engine.

When the pull start gets locked, you have to release water pressure from the wand. I had the same problem last year.
0helpful
2answers

I cant pull the cord, everything seems to be frozen

It is possible the motor is seized or the pump component has jammed. The Honda Motor usually has an oil minder(wont start if low oil). So that being the case you may have a problem with the pump. If you are handy and have internet it is possible to download a parts/repair manual for the type of pump involved. Otherwise take it to a repair shop. Sometimes these pressure washers are more costly to fix as compared to a new one..
0helpful
1answer

I try to pull the rip cord but it just gets stuck and i cant start it how do i fix it

IF YOU HAVE BEEN USING THE PRESSURE WASHER AND THEN TURNED IT OFF,THERE WILL STILL BE PRESSURE IN THE HOSE.YOU WILL NEED TO SQUEEZE THE TRIGGER ON THE GUN WHILE YOU START THE ENGINE.
0helpful
2answers

Cant start the unit ,there is to much pressure on the pull chord when water is hooked up.

Trying to start a pressure washer with water supply on and gun trigger off will be a difficult task. It could be comparred to trying to start a lawn mower with the mower in tall grass. Place the mower on the drive or walkway and pulling the rope to start the engine is much easier. It is easy to start your pressure washer with no water in the system however there is a remote possibility that you could overheat the seals if you take too long to turn on the water. It is a little more difficult to start the washer with water supply on and someone holding the trigger to wand open. This will prevents pressure from building and making engine hard to start. You will not damage your washer if you start it with water supply off if you flood the pump and pressure hose with water first . Here is the procedure I use if i am working alone. I trun on the water to pump and open trigger to gun to allow water to flow into pump and pressure hose. Turn off water (leaving the water supply on will make it a little harder to pull starter). Start engine while holding trigger to gun open. When engine starts release gun causing unloader to activate circulating water in pump. Now turn on water and you are ready to work. If your system is under warranty however, I would advise to use the starting procedure outlined by mfg (hold open trigger to gun however). To get the longest life from unit try using it at say 75% of capacity or lower if your can and use max pressure on the tuffest jobs. Leaving your washer at full pressure for all jobs is like driving your car at 100 mph everywhere your go. Good luck.
1helpful
1answer

Pull rope wont retracxt all the way

coil spring inside needs to be recoiled or tab is broken or off the hook
pull the rope assembly off and inspect/ repair or replace
4helpful
2answers

Let go of wand trigger pressure will not come back

spill valve is stuck and needs to be cleaned and greased common problem....also check all connections for blockage in line
0helpful
1answer

Too much pressure.

You need to keep the trigger pulled every time you start and you need to run the water for 3-5 minutes wide open before you start. Zero air should be in the line or this could cause it to **** out. You probably damaged the pump at this point.
1helpful
1answer

Wont pull detergent

problem is that u have to use with lowest pressure i believe black tip
0helpful
2answers

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even...

Difficult to know from here, check all the screws see if there was a required strenght on some of the screws. You should take it apart and assemble again.
Not finding what you are looking for?

766 views

Ask a Question

Usually answered in minutes!

Top Honda Garden Experts

JOHN LAPIER

Level 3 Expert

2602 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Ron
Ron

Level 2 Expert

195 Answers

Are you a Honda Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...