Question about Hotpoint-Ariston LI 640 24 in Builtin Dishwasher

1 Answer

Hi, our ariston dishwasher has stopped before the cycle finished and the water has not drained out. There are 2 flashing lights - the brush emblem and the spray ' on a tilt' emblem (the 2 on the far right of the pictures on door). We've checked and there is no clogging up of rubbish. Help!

Posted by kezzav on

Ad

1 Answer

Kelley Jones

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 27 Answers

Error messages.
The dishwasher is equipped with a
safety system which is able to
detect any operating anomalies.
These anomalies are signalled by
the rapid flashing of one of the
wash cycle indicator lights M.
If the indicator light for the soak
cycle flashes (see wash cycle table),
cancel the wash cycle by following
the instructions indicated in the
"Modifying a wash cycle in
progress" paragraph on page 4.
Now check whether there is any
water in the mains supply and that
the tap is turned on; if the error
message persists, then call for
technical assistance, indicating
which message appeared.
If the indicator light for any wash
cycle apart from the soak cycle
flashes rapidly, turn the appliance
off and call for technical
assistance, indicating which
message appeared.
Troubleshooting
You have checked
everything, but the
dishwasher still doesn't
work and the problem
persists?
Call an authorised service centre
near you and remember to mention:
? the type of malfunction
? the model mark (Mod?.) and the
serial number (S/N?.) indicated on
the rating plate located on the inner
door, to one side.

If you need further help, reach me via phone at https://www.6ya.com/expert/kelley_9a924afdf232bd4d

Posted on Jan 14, 2018

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why Ariston lbf51 washing and drying light rapid flash


AL03 - Drain Timeout (drain problems)
LED 1 (washing) and LED 2 (drying) flashing.

Probably the siphon of the apartment is clogged.
  • Remove the drain hose and make sure that is not clogged.
  • Drain water in a bucket.
  • If the dishwasher drains the water, clean the siphon of the apartment.

24501411-0h3kxpflbez5mdeb5anq3st4-5-0.jpg
Dado

May 25, 2014 | Ariston Technologies LL65 Built-in...

1 Answer

L 63 B NA Ariston


Your dishwasher is equipped with a safety system which is able to
detect any operating anomalies. These anomalies are reported by
one or two wash cycle indicator lights "G" flashing rapidly.

24238319-0h3kxpflbez5mdeb5anq3st4-3-0.jpg In this case could be:
  • Drain motor disabled
  • Filters clogged
  • Drain hose blocked

Dado

Apr 24, 2014 | Ariston Technologies Dishwashers

1 Answer

Hi, I have an Ariston LL64 model dishwasher that doesn't complete a wash cycle. It gets so far and stops with the "crystal care" light flashing. Any ideas? thanks Barry


It is possible that the machine does not start off the cycle because there are errors or feedback from the inputs. For the program to start up the main program controller must initiate the INLET/PUMP MOTOR/DRAIN to work when it is commanded .If this does not happen then the voltage at these points must be checked or the fault relates to no voltage/drive from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor. The water pressure must be good and the spraying must be seen to be good. If not the pump must be checked for clogging.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the drain valve/pump activated so as to drain off all the water.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.espares.co.uk/advice/dishwashers/a/3

Aug 03, 2011 | Ariston Technologies LL64WNA Built-in...

1 Answer

Green start button won't stop blinking


START/RESET status indicator light flashing


You have pressed the indicator light flashing START/RESET pad while the START/RESET dishwasher is running. This will cancel the cycle. The light will stop flashing after the dishwasher drains (about 90 seconds).


Press the pad once to start the dishwasher. Press the pad a second time when the dishwasher is running only if you wish to cancel the cycle.


Power to the dishwasher was turned off while a cycle was running and power has just been restored to the dishwasher. The blinking lights indicate that the dishwasher is draining the potential water inside.


The light will stop flashing after the dishwasher drains. A new cycle will start automatically.


Good luck

Nov 29, 2010 | General Electric GLD6966RSS Stainless...

2 Answers

Ariston LS 2020 taking more than two hours to go through cycle.


Ariston and on and on...lol

The water temp thermostat is to blame or the water is not heating.Basically what happens is the washer fills with cold water and starts to wash and heat at the same time.Once the water reaches a certain temperature it moves onto the next stage of the wash program.If the water is not heating or the thermostat is not working the programmer wont get the signal to move on.Hope this helps.

Apr 26, 2010 | Ariston Technologies Dishwashers

1 Answer

Eco and rapid cycle light flashing rapidly.wash cycle not finished. still has water in bottom of machine


had something jamming pump impeller which prevented machine pumping water out. The motor is connected by a bayonet fitting to the pumpand is easy to get at and clear obstruction.

Dec 17, 2009 | Ariston Technologies LL64WNA Built-in...

2 Answers

Ariston dishwasher


i have a brand new ariston ll-64 and the wash cycle won't start and two flashing lights

Feb 09, 2009 | Ariston Technologies L63 Free-Standing...

1 Answer

L63 Salt light is flashing


goes for short time and 2 ljghts flash the red salt light wont go on

May 16, 2008 | Ariston Technologies L63 Free-Standing...

Not finding what you are looking for?
Hotpoint-Ariston LI 640 24 in Builtin Dishwasher Logo

Related Topics:

151 views

Ask a Question

Usually answered in minutes!

Top Hotpoint-Ariston Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18626 Answers

Are you a Hotpoint-Ariston Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...