Question about GE D52GW12 52" Rear Projection HDTV-Ready Television

1 Answer

ON our GE D52GW12 52" AFTER TURNING TV ON IT

Posted by r_barnett3 on

Ad

1 Answer

Sonny Berry

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GE Master
  • 8,617 Answers

Try resoldering the flyback transformers connections on the board. Its very common for the flyback pins to develope cracks around the pins which can cause that issue. I would check that first with that model.

Posted on Jun 13, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

TV is in "now scanning" mode and I can't get it out.

Maybe try turning the TV off, or unplugging it for a couple minutes. Seems there are alot of problems that can be fixed by unplugging a tv for 10 to 20 minutes.
0helpful
1answer

GE TV Model 35GT695 - Problem Turning TV ON

Sounds like a solder problem. Look over the circuit board real good ffor cracked solder joints especially near the flyback and your Horizontal output and regulator transisitors. Could also be a defective capacitor look for signs of bulging or leaking capacitors.
0helpful
1answer

When turning on it flashes green for a second and immediately begins flashing yellow... there are 2 red lights that turn on and blink a couple of time off to the side marked "temp" and...

Hello,
Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement. Hope this will help in solving the problem...
1helpful
1answer

Have a GE Profile Arctica that is a few years old. It is "clicking" every couple seconds, like turning off and on constantly. I have been gone for a week if that matters. The HRS light is...

. Cut everything off for a few minutes then turn it back on and listen for a click from the compressor relay as the compressor tries to start.
Is the compressor motor running.If no check starter/overload relay. The relay is a small usually black cube shaped electrical part plugged into the compressor or wired to it nearby. It may appear burnt or rattle when shaken if it's bad. The two connections should show continuity with an amp meter. If it's good then it's most likely the compressor causing the problem.
0helpful
1answer

I have an older-model GE washing machine. About 2 weeks ago I went down to put clothes in the dryer & the washing machine was still full of water but the dial was in the "off" position. I...

Sounds like your timer is going out. Turn it to the spin cycle and see if it'll spin. If not jiggle the timer handle and see if that does it. If it works after jiggling the handle then you need a new timer which can be expensive. Or on the cheaper side it could also be a lid switch but sound more like a timer. Check the lid switch also.
0helpful
1answer

Hi, I have a Sony KDL-46XBR9 LCD Digital Color TV. This morning my son was watching cartoons and it clicked itself off. It has sometimes done this in the past, so we did something else for a couple of...

This tv have a power supply board is the causes and the problems.Ur tv power supply board finally gave out and not supply the right voltages to the tv system anymore.That the board,where the tv power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
2helpful
1answer

While setting up the Crest Universal remote control RCP1F for my sharp TV, I've managed to turn the TV off, but now I can't turn it back on. The TV remains on Standby and turning off the power doesn't do...

OKAY TRY THIS..
DO STEPS 1-3 AGAIN AND ONCE IT TURNS OFF KEEP CLICKING THE CURSOR UP A COUPLE TIMES.
THEN START CLICKING THE CURSOR DOWN SLOWLY TELL THE TV TURNS BACK ON AND ONCE IT CLICKS BACK ON HIT THE TV BUTTON ON THE TOP OF THE REMOTE ..
IF THE LIGHT BLINKS TWO OR THREE TIMES MORE THEN LIKELY YOU'VE PROGRAMED IT =)
AND NOW KICK BACK RELAX AND ENJOY A COLD BEER FOR THE BOTH OF US =)
Not finding what you are looking for?
GE D52GW12 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

203 views

Ask a Question

Usually answered in minutes!

Top GE Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76823 Answers

Cindy Wells

Level 3 Expert

6394 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Are you a GE Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...