Question about Kodak i65

1 Answer

Is there a wia driver for Windows 7 for the Kodak i65 Scanner?

Posted by sgregson on

Ad

1 Answer

joelgilb

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Well I too HAD this problem. Upgraded to Win7 64 bit and was unable to install the existing 32 bit drivers (of course) that operate in WinXP and Vista. Called Kodak and there wonderful answer was Buy a New Scanner.

Well this was just not an option. SO I searched and searched for alternatives, to creating a WinXP Virtual machine with VMPlayer or VirtualBox to remote controlling an older WinXP laptop connected to the scanner. None were solutions I felt I could live with.

Then I found VueScan at www.hamrick.com. A small chea scanning software that you can try before you buy. I read through everything on the site including the specific scanner notes for the Kodak I65, then downloaded the trial version.

Once installed you follow the instructions from the site to use VueScans own driver to run the Kodak scanner and lo and behold I got my ORIGINAL Kodak scanner menu to work on Win7 64bit. Then I used the VueScan software to scan a document and it worked like a charm. Albeit with the VueScan watermark.

Now I could have stopped there and called it a success, but I then, tried scanning with my Nitro PDF Pro software and was amazed to get a Perfect scan without the watermark.

Now NOTE, I did not buy the VueScan software at this time, as I don't need it's ability. I just used their driver and driver installation instructions from the website specifically for the Kodak I65. Most likely going to buy the basic version of the software anyway, as I think the guy deserves something for saving my EXPENSIVE I65 from becoming a paperweight.

An Elegant and Complete solution to Kodak's total support failure!

N

Posted on Sep 20, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hp deskjet 5100 wia driver


I don't know why your scanner is not working
This printer is supported by Windows 7. Therefore, if you are using Windows 7, you might try rolling back the driver, or updating it, or uninstalling it and letting it re-install next time you connect it/reboot the computer. All these things are done from the hardware device manager > printers in the OS
As WIA is contained within Windows, rather than an additional driver from HP, the steps above should resolve any issues that are due to a corrupt driver.
If you are using a Mac read this
http://h30434.www3.hp.com/t5/Mac-Printing-and-Scanning/Officejet-5100-won-t-scan-to-Mac/td-p/1967991
This may not be why the scanner is not working though.
24.January.2015

Apr 20, 2014 | hp deskjet 5100 series

1 Answer

My scanner model is canoscan lide25 instalation software free download F910111


check out this solution by get the software re-installed.

1. http://www.downloadatoz.com/driver/download_31895,canon-canoscan-lide25-scanner-wia-driver-v1-2-1-0-windows-xp.html

2. http://www.downloadatoz.com/driver/item_canon-canoscan-lide25-scanner-wia-driver-v1-2-1-0-windows-xp.html

Apr 05, 2011 | Canon CanoScan LiDE 25 Flatbed Scanner

1 Answer

I have a Canon 4200F scanner and recently purchased a new computer with Windows 7 that is 64 Bit. When I try to use the scanner get a message that I need a WIA driver to use this device. Can you please...


Hi bjgestel !
This means there is no more support from HP for your unit under Windows 7 but Windows has a compatible driver included in it's system ( WIA ) .
The scanner should run smooth but with some restrictive functions . Normaly , it should run without having installed the HP XP driver/ sofware . If this not your case , there is a workaround after you installed the XP driver and made sure installation was successfull . The scanner will need to run with a third party application . Download FreeKapture from
http://download.cnet.com/FreeKapture/3000-2094_4-10673689.html
Launch Freekapture , clic on Scan , select WIA-Hewlett-Packard . Your scanner will run . If you choose HP's software, program will hang .
Note : no slides or negatives scans possible in WIA mode but the rest works .

Good luck !
fanaudi .

Feb 22, 2011 | Office Equipment & Supplies

1 Answer

Need wia driver for windows 7 32 bit. factory drivers don't work


In any case , make sure the factory driver is correctly installed . If there are no driver available under W7 , install driver XP .
Download and install Freekapture ( http://download.cnet.com/FreeKapture/3000-2094_4-10711598.html )
Load FreeKapture , clic on Scan and select WIA-Canon DR2020U .
Hope it helps ,
Regards

Jan 04, 2011 | Canon DR2020U Flatbed Scanner

1 Answer

It does'nt support with windows 7


I'm afraid there are no drivers running under Windows Seven for this unit.
If you have the W XP install disc , you could install a virtual version of W XP on your HDD ( http://downloads.vmware.com/d/info/desktop_downloads/vmware_player/3_0 )
You could also partition your HDD ( http://www.partitionwizard.com/free-partition-manager.html ) and install W XP on the new one .
Otherwise , you will have to buy a new scanner .
Regards .

Dec 28, 2010 | Kodak i65

1 Answer

Scanjet 4470c. Can't get it to work with Windows 7. Any ideas on a solution or is there a Windows 7 driver out there?


Hi ,
I succeeded to make my Scanjet 4470c run in WIA mode under W7 32-bit Ultimate . Should also work with W7 64-bit .
Make sure driver XP ( yes , XP ) is correctly installed .
Then , download and install FreeKapture ( yes , it's free ) from here : http://download.cnet.com/FreeKapture/3000-2094_4-10673689.html
Load Freekapture , clic on Scan and select WIA-Hewlett-Packard . Scanner works fine in this mode but if you choose HP PrecisionScan Pro , program will freeze .
In any case , no slides or negatives scans possible but the rest works .
Regards .

Dec 13, 2010 | HP Scanjet 4470c Flatbed Scanner

1 Answer

Trying to load CanonScan N124OU onto Windows 7 and get error message "there is no application registered for this event"


canon scan n1240u will work on Win7


here's how:

go to this site: http://www.usa.canon.com/cusa/support/consumer/scanners/canoscan_series/canoscan_n1240u#DriversAndSoftware

click "Drivers and Software" then select OS "Windows XP" then download "WIAdriverN670UN676UN1240U.EXE"

Install the WIA driver on your Windows 7 OS and used only mspaint to capture image on the scanner


TWAIN doesn't work on Win7 but WIA still doesGood Luck!

Dec 06, 2010 | Canon CanoScan N1240U Flatbed Scanner

1 Answer

I have canoscan n1240u but I can't use it with windows7 ...How can I do?


canon scan n1240u will work on Win7


here's how:

go to this site: http://www.usa.canon.com/cusa/support/consumer/scanners/canoscan_series/canoscan_n1240u#DriversAndSoftware

click "Drivers and Software" then select OS "Windows XP" then download "WIAdriverN670UN676UN1240U.EXE"

Install the WIA driver on your Windows 7 OS and used only mspaint to capture image on the scanner


TWAIN doesn't work on Win7 but WIA still does

Good Luck!

Nov 28, 2010 | Canon CanoScan N1240U Flatbed Scanner

3 Answers

All of pics not loading into computer


This worked for my Kodak C913...from Kodak Support.

To switch between the Microsoft WIA drivers and the Kodak camera driver:
1. Connect your camera to your computer.

2. Turn on your camera.

NOTE: If the WIA drivers automatically detect your camera and display a window for transferring images. Click Cancel to close this window.

3. Open the Device Manager.

a. Right-click My Computer and select Properties.
b. In the System Properties window, select the Hardware tab.
c. Click Device Manager.


4. Click the plus (+) sign to the left of Imaging Devices or Universal Serial Bus Controller, depending on the version of Kodak software installed on the computer. Your Kodak camera should be listed.

5. Double-click on your camera model name.

6. Select the Driver tab.

7. Click Update Driver.

8. If you have installed Windows XP Service Pack 2 or above, your system displays the Hardware Update Wizard. Select No, not this time and click Next.

9. Select Install from a list or specific location (Advanced) and click Next.

10. Click Don't search. I will choose the driver to install and click Next.

11. Select the Digital Still Camera for WIA drivers if you having trouble using the Kodak drivers, or select the Kodak camera if switching from WIA to Kodak and click Next.

12. Click Finish to complete the driver update.

13. If the program selection window appears, select Windows scanner and camera wizard
14. Select Always use this program for this action and click OK to transfer your pictures.

Dec 21, 2008 | Kodak EasyShare C913 Digital Camera

Not finding what you are looking for?
Kodak i65 Logo

2,495 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Cindy Wells

Level 3 Expert

6181 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...