Thanks Hey Thanks a bunch. Thats what I wanted to know. I have yet to have it work but Ill keep trying. I assume you wait 7 seconds after pushing the button rather then after the shutter clicks Thanks again

Welcome to Fixya.

Please try the following steps to resolve this problem - this same procedure worked for my colleague :

• Power off printer
• Hold down STOP/RESET button then Press and Hold down Power button
• Keep Power button down and Release STOP/RESET button
• Push STOP/RESET button twice
• let go of power button
• Wait 20-30 seconds - my display shows "canon Idle"
• Then Push STOP/RESET button four times
• Push Power button twice
• Power off (shut printer down)
• Wait for at least 5 seconds and power it back on

This should do the trick and will get you printing again in no time.

Thanks for using Fixya.

ther should be a button on the door opener that you push ,it will light up and scat over to your car and just push the button. thats it, you car is the same as the remote its just got on heck of a big battery
hey if'n i was of help tell me so i know.. thanks jay

Hey--  You've spent a bunch of time on this already, so let's figure it out. The first step is to check power connections. L1, L2 , Neutral for proper location and tight connections. Should have 120v and 220v checked at bus block. If these check out, then this new unit should be under warranty and qualify for service. Not unheard of bad board or loose wire on a new unit. Let a tech sort it out on site. Let me know if this info helps- have more if needed-  Thanks-  Ed

How To Reset Waste Ink Canon Pixma MP450

Hi there
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.


Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Release power button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

How To Reset Waste Ink Canon Pixma MP450
OK try see if this will do
Hi there
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.


Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Release power button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi Friend

please follow the steps

1. Switch on the router.

2. Now at the back of the router push and hold the RESET button for 30 seconds and after that release the button and unplug the power cable form back of the router and wait for another 30 seconds and plug the power cable back.Wait until the power light becomes solid and steady.

3. Connect the computer to the router either of the four ports named 1 2 3 or 4 and the internet wire into the internet or WAN port.
4. Click the start menu and RUN, type cmd and hit enter.

5. In the black box type ipconfig /all and hit enter. Out of those bunch of information please note down the default gateway.

6. Open the internet explorer and in the address bar type that default gateway number. You will get the router page.

7. You can configure as per your requirements now.

Enjoy

Regards
Chiranjeet

Resetting Oil Service Light on your 2002 - 2006 MINI Cooper and Cooper S, and 2007 - 2008 MINI Convertibles:

1) Press and hold the trip button
2) Insert key and turn to position 1
3) Watch for RESET to appear
4) Release the button, then press & hold it again
5) Wait for the RESET to flash
6) Release the button, and then press & release (once only)
7) Service interval should then be reset to next interval
If that didn't work, try this:
1. Push the Trip Button
2. Turn ignition key to position 1 and 51A will appear to left of mileage
3. Release trip button
4. Wait 3 seconds
5. Push trip button
6. Wait (5-8 seconds) for RST to appear in left corner
7. Release trip button
8. Push trip button
9. 15000 will appear as new service interval
10. Release trip button

Or this:
1. Press and hold the trip odometer button.
2. Insert car key and turn it to the fi rst position (not the second position).
3. You will see 51A come up in the trip odometer area.
4. Release, then press and hold again.
5. Watch for the word “RST” to appear on the Odometer indicator.
6. Release, then press and hold again.
7. Wait for the “RST” message to fl ash.
8. Release, and then press & release (once only).

Sound like you have a bad cv "constant velocity joint " REPLACE.

The first thing you need to do is to clear your old codes then drive

and see if they come back .

1. Re-enter back into the climate control panel and after all the codes display the display will stop at PCM?

2. Push and release the FAN UP (^) button on the climate control panel and you will see PCM DATA?

3. Keep pushing and releasing the FAN DOWN (v) button until you see PCM CLEAR CODES?

4. Push and release the FAN UP (^) button and you will see PCM CODES CLEAR?

5. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

6. Push and release the FAN DOWN (v) button and you will see IPC?

7. Push and release the FAN UP (^) button on the climate control panel and you will see IPC DATA?

8. Keep pushing and releasing the FAN DOWN (v) button until you see IPC CLEAR CODES?

9. Push and release the FAN UP (^) button and you will see IPC CODES CLEAR?

10. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

11. keep Pushing and releasing the FAN DOWN (v) button and you will see ACP?

12. Push and release the FAN UP (^) button on the climate control panel and you will see ACP DATA?

13. Keep pushing and releasing the FAN DOWN (v) button until you see ACP CLEAR CODES?

14.Push and release the FAN UP (^) button and you will see ACP CODES CLEAR?

15. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

16. keep Pushing and releasing the FAN DOWN (v) button and you will see SIR?

17. Push and release the FAN UP (^) button on the climate control panel and you will see SIR DATA?

18. Keep pushing and releasing the FAN DOWN (v) button until you see SIR CLEAR CODES?

19. Push and release the FAN UP (^) button and you will see SIR CODES CLEAR?

20. Wait 5 seconds and then keep pushing the OFF button until you see PCM?


21. Push the AUTO button to get out of diagnostics.

22. Turn ignition OFF for 15 seconds.

23. Re-enter diagnostics and see if any history codes re-appear.

wait a minute you wanted me to pay you to tell me how to fix it... now you want me to tell you how i did it ...no thanks ...well for 9.99 a month ill tell you...no thanks

About middle of the board you removed the flyback,there is a u shaped heat sink this is in the middle of the board,behind the heat sink is a blue cap 2200 uf ,if the top is pushed up the cap is bad.