Question about Uniden Radio Communications

1 Answer

Uniden MC 610 Marine Radio

I have a Model MC 610 that no longer seems operable. Is there a basic charge for inspecting the unit? It turns on i.e. lights up, but no sound comes out if you turn the volume up. Is it worth fixing?
I am looking at buying a Uniden Oceanus model if this is not repairable. Will the antenna connection on the Oceanus be the same as on the MC 610?
Thanks for your help.

Posted by rayorsandy on

  • rayorsandy Aug 19, 2008

    No guidance was given on the adaptability of the connections between the old unit and the Oceanus.

×

Ad

1 Answer

Patrick Patterson

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

While your MC610 was a great radio for it's time. the Oceanus is an excellent choice to replace your MC610. Unforunately you would be looking at about a $100.00 repair bill to repair your MC610. for just a little more you get a new radio and the new radio will have a warranty.

Posted on Aug 19, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change language on pioneer deh4600bt


Section
02
Using this unit
(iPod control)
c
This unit's iPod function is operated from your
iPod.
d
(Bluetooth indicator)
Set up menu
1
After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
2
Turn M.C. to switch to YES.
# If you do not use the unit for 30 seconds, the
set up menu will not be displayed.
# If you prefer not to set up at this time, turn
M.C. to switch to NO.
3
Press M.C. to select.
4
Follow these steps to set the menu.
To proceed to the next menu option, you need
to confirm your selection.
LANGUAGE (multi-language)
This unit can display the text information from a com-
pressed audio file even for information embedded in
English, Russian or Turkish.
! If the embedded language and the selected lan-
guage setting are not the same, text information
may not display properly.
! Some characters may not be displayed properly.
1 Turn M.C. to select the desired setting.
ENG (English)-??? (Russian)-TUR (Turkish)
2 Press M.C. to confirm the selection.
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
4
En
FM STEP (FM tuning step)
Use FM STEP to set FM tuning step options (seek
step settings).
1 Turn M.C. to select the FM tuning step.
100 (100 kHz)-50 (50 kHz)
2 Press M.C. to confirm the selection.
QUIT appears.
! The manual tuning step is fixed at 50 kHz.
! When AF and TA are turned off, the seek step is
fixed at 50 kHz even if set to 100.
5
To finish your settings, turn M.C. to se-
lect YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO.
6
Press M.C. to select.
Notes
! You can set up the menu options from the sys-
tem menu and initial menu. For details about
the settings, refer to System menu on page 19
and Initial menu on page 23.
! You can cancel set up menu by pressing SRC/
OFF.
Basic operations
Important
! Handle the front panel with care when remov-
ing or attaching it.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight and
high temperatures.
! To avoid damaging the device or vehicle inter-
ior, remove any cables and devices attached
to the front panel before detaching i

Feb 08, 2015 | Pioneer Deh-5400bt Car Stereo...

1 Answer

Cannot get battery to charge


The battery may be unable to charge and probably will have to be replaced.

Oct 21, 2014 | Pyle Pro PWMA1090UI 800W Dual Channel...

1 Answer

How do i remove error 4200-0099296


As an error, the C-4200, refers to laser unit. Sometimes the main charge (mc) cause this error. Remove the mc and check the sound of the laser. If you don' t hear the laser sound, then the problem is the laser unit

Sep 25, 2014 | Kyocera FS Office Equipment & Supplies

1 Answer

Compressor comes on for about 1 minute, but fan doesn't. Then a sound like a pressure release valve opening starts and will continue until you turn the unit off. The unit will sometimes work normally...


The sound is from the compressor high side pressure exceeding design limits due to the fan not operating, the fan pulls air across the coil to remove heat from the freon which keeps the pressure down. The capacitor or fan motor may be bad. Need to open unit panel and visually inspect the capacitor for swelling, (rounded top should be flat) where the wires connect. Also use meter to test mfd of capacitor. May only need capacitor replacement, most common failure on this unit.
If not corrected damage can be done to the compressor due to overheating.

Aug 24, 2011 | Heating & Cooling

1 Answer

I have a Rinnai Model 2532 with an MC-45-4US and BC-45-4US control units. I finished another bathroom and want to add a controller, but have been told that a compatible BSC-45-4US is no longer made. Is...


Sorry Ken I worked for Rinnai Australia as a service manager so treat my advice with a little cuation but you should find the basic universal controller should work fine. The code over here is a MC-91 Q2A. It will MC-91 sometihing for over there (I'm guessing from the codes you use you are across the pacific!). You can wire this unit either back to the heater or to wiring from another controller, just match the colours and link them in. Power off the heater first but it is all low voltage.

May 26, 2011 | Rinnai Digital Remote Water Heater Control...

1 Answer

Wont turn on


No, most units will at least work basic functions without a remote. What is the make / model? I would take it back as soon as you can.

Jan 19, 2008 | Audio Players & Recorders

1 Answer

Canon DC20


This happens alot at work its either the charging part is broke or its the mainboard inspect the port for damage if its ok then inspect the ac adapter for damage as well, if you have time you could go to best buy and ask to use a charger from a floor model if it doesnt work then it needs to go in for repair sorry.

Dec 21, 2007 | Canon DC20 DVD Camcorder

1 Answer

Scanner error


sounds like a bad power supply or hvt, have it checked out, can be dangerous

Dec 02, 2007 | HP 610 Color Copier

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Radio Communications Experts

Robert McClure

Level 2 Expert

161 Answers

eradiostore
eradiostore

Level 3 Expert

1658 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Uniden Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...