Question about Shurflo On Demand Diaphragm Pump 28 Gpm 12 Volt 12in Model 12021000

1 Answer

Shurflo pump 20psi 2095-204-112, in motorhome runs normally when supplying wash hand basin with hot or cold, but when supplying hot or cold to kitchen sink the pump runs intermittently with very little pressure.

Posted by jo_stgrain on

Ad

1 Answer

Paul Beyer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 528 Answers

Take the aerator off the faucet and see if that makes it work better if yes clean the filter in the aerator on the kitchen faucet.

Posted on May 12, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Shurflo 2088-403-144 5.8amps 45 psi 2.8 gpm in my motorhome it won't operate I tap the pump lightly with the back of a hammer & it will operate for about a minute then stop ,


Try just replacing the pressure switch first. The contacts in that switch burn with time and it isn't necessary to replace the whole pump.

Feb 20, 2018 | Home

1 Answer

Hi, is there a way to make the hot water hotter in a 2016 Jayco Journey. The water is just hot enough for showering but not hot enough to wash the dishes.


remove the unit that mixes the hot and cold water at the hot water system to prevent scalding of people
it is fitted there by law but unfortunately the plumbers who fit it are not willing to fit it where it is supposed to be fitted ( baths , showers and hand basin taps and lines )
better and cheaper to fit just one than several
it is not required for sinks and dishwasher and washing machines lines
anyway the human hand cannot stand water over 75 c as that when burns occur so having hotter means that you have to add cold to be able to put your hands in the water and that sort of defeats the purpose of having hotter water

Apr 05, 2017 | Home

1 Answer

Power to pump


put a little oil on it and turn it by hand a few times it gets dirty from sitting ,try it

Mar 28, 2014 | Shurflo Pumps 8005-233-236- Shurflo

1 Answer

Hi! My hot water taps from the wash hand basin and mixer bath has low pressure. I`ve got a combi boiler in the first floor. Can I install a single impeller pump connected from the hot water outlet from the...


In a word no. Combi boilers work on balanced pressure.ie the mains cold supply to the boiler should be around 1 bar minimum which would give a hot water pressure of the same 1 bar. Assuming the cold water pressure is fine, it sounds like you have a restricted flow on the hot side. If you live in an area with water problems the hot water systems pipework calcify over time effectively reducing water flow. Unless any flexi hoses are kinked, check if there are any filters in the appliances that may be blocked.Also check all valves are fully open and if possible check if there are any restrictions at the valves. Failing all that and the taps are in good order it is possible to fit a pump before the boiler but this may only be a temporary fix overall.

Apr 04, 2010 | Plumbing

1 Answer

How best to install 3.5 atmosphere water pump to drive shower, bath, toilet and wash basin to two bathrooms, particularly connections to cold and hot water supplies?


Typically a water pump or booster pump would be placed on the main water feed (this assumes this line feeds not only the main cold line but the hot water system too. I work heavily with booster systems and would ask for futher information. Is this system runing off of a pressure switch such as starting a lower pressure and will shut down at a higher pressure or is it a constant pressure system where as the pump is expected to slow down or speed up to met demands? Either way the system will require a pressure tank, the first method of running will require a larger tank. With regadrs to connection this could be sweat in (with copper) or the use of mechanical connections. A proper "spring loaded" check valve would be required too.
I hope this may have helped,
Tom

Sep 21, 2009 | Plumbing

1 Answer

How do I fix water slowly pouring into the basin?


if this only happens when you selected cold water and water runs normal in the hot shut cold water remove the cold water hose and clean the screen that maybe in the hose and clean the screen in the valve that hooks to the hose once removed this will solve this problem

Aug 26, 2009 | Frigidaire Washing Machines

1 Answer

Do anyone know what e11 mean on hotpoint wd71 pls


It means "No hot/cold fill" and recommends - Check the water supply, inlet valve and hot and cold hose connections.

Mar 27, 2008 | Washing Machines

2 Answers

Hoover 750L top loader washing machine


I had this problem. I alternated the hot and cold water valves (changing over the wiring) and then hot tap then dribbled instead of the cold. Replacement part i believe is around $35AU

Dec 29, 2007 | Washing Machines

1 Answer

My gwl 15 ecosmart


having the same problem myself i am replacing the soliniod when it get here. in the mean time the hot water runs in normally so i swapped the hoses over on the back and and now i can wash just that the hot is now the cold button

Dec 04, 2007 | Fisher Paykel EcoSmart GWL15

Not finding what you are looking for?
Shurflo On Demand Diaphragm Pump 28 Gpm 12 Volt 12in Model 12021000 Logo

1,155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Shurflo Plumbing Experts

Bill Johnson

Level 2 Expert

306 Answers

Brad Brown

Level 3 Expert

18563 Answers

Tom Chichester

Level 3 Expert

61131 Answers

Are you a Shurflo Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...