- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
the PGBK ink cartridge might not be getting a good connection you might have to remove it and check the connections or clean the connection bars
You might have to uninstall the printer restart your computer then reinstall your printer click start control panel administrative tools computer management device manager scroll to ports(COM&LPT) + to expand you should see a communication port and Ecp printer port you might see a yellow? ! question exclamation mark or a red X this will mean you need to install a new driver for this device right click you will have options to update driver,disable,uninstall or select properties again you will have the similiar options also you can troubleshoot the device hope this helps you
This is common problem with Brother Printers. I am going to assume you are using Non-Brother branded ink cartridges. Brother cartridges have a cleanser in the ink that most generic cartridges don't have. This in turn causes the jets to clog and not allow ink to pass through them. The fix is to go buy a couple of Brother cartridges and do a cleaning with those cartridges. You may spend some money doing this as a cleaning wastes a lot of ink, but it will clean the injection lines and fix the printer. You could also consider buying a new printer. I know this is not the answer you were looking for, but it is the true answer. I just bought a new printer due to this fact.
In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.
Make sure you install the correct type of KODAK Ink Cartridge for your printer. Currently we offer two types of ink cartridges (10 Series and 30 Series). Installing the wrong type of ink cartridge may result in this error. You will need to install a new, correct type of KODAK Ink Cartridge. NOTE: For more information, see Which ink cartridges to buy for all-in-one printer.
If you are using the correct type of KODAK Ink Cartridge, reinstall the color ink cartridge.
Wait until the printhead is idle and silent, then pinch the latch on the color ink cartridge with your thumb and forefinger and lift it out of the printhead.
Install the color ink cartridge back into the printer, making sure to press down on the thumb tab until it clicks into place.
Close the printer access door. For printers with LCDs, follow the instructions on the LCD screen. For more information on installing ink cartridges, see the Extended User Guide for your printer. Review Maintaining Your Printer - Replacing ink cartridges.
If the error continues, restart your printer:
Turn off the printer by pressing the power button.
Wait five seconds.
Turn on the printer.
If the error continues, and you have extra, new KODAK Ink Cartridges on-hand, try to install a new ink cartridge (or a set of new ink cartridges).
Thanks for using Fixya.
You won't need to drill hole anywhere.
Visit this link to get all the instructions required to refill the ink in Epson T0711 cartridge.
But remember you would need a chip resetter gun to re set the chips on the ink cartridges after you refill the cartridges.
Visit this link to buy Universal chip reseter if you don' t have.
Hi there Dell Printer 944 error message 1102 Please unplug the printer from the wall. Now remove the power brick from the back of the printer for 60 seconds. Now plug everything back in. This will reset any error messages the printer has. Now open the printer with the power on and the cartridges should go to the center to be replaced. Take out both Dell Series 5 ink cartridges and make sure the tape is off the cartridges and insert both back in and make sure the seat properly and latch. Close the printer and it should print an alignment page. If you still get the error message Why does my Dell ink cartridge level still show up as "low ink" after refilling them? Dell ink cartridges have a sensor that reports the ink level as low once it reaches a certain level. The sensor can not be reset. If you refill an ink cartridge that previously reported low ink, it may print fine, but the sensor will always report low ink. Buying or replacing ink cartridges with new Dell cartridges will resolve the low ink message. Dell discourages ink refills. Refilling ink may lead to print quality problems, and even eventual hardware problems. This post is in no way a validation of refilling ink cartridges. Why my printer is reporting “low ink" after using refilled/remanufactured ink cartridges? Most ink cartridges have sensors that report the ink level.The “Low Ink” is usually the last sensor (fuse) before running out of ink. Since the sensors are fuses that open when the ink level drops, they cannot be reset.If you are using refill or remanufactured ink cartridges, the best thing to do is to disable “ink alerts” on the printer’s software so you don’t keep getting “low ink” messages. To disable “Ink Alerts” on Dell inkjet printers: 1.Open the Dell printer software (All-In One Center, Tool Box, etc) 2.Go to Settings 3.Advanced 4.More Options 5.In the “Appearance Mode, window, check “Never display the Printing Status window” and “Display the low ink alert only when the cartridges are almost empty. Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
just open the cover .when you open the cover cartridge will come to center just pull all the cartridges one by one don’t make pressure too hard it will come easily if you put more pressure and try to removing it and it is not come out then don’t do it may be you doing wrong . let it be and take help from some one who using printer and know how to fix the cartridges. Have a nice day and do not forget to rate please...!
Forgive me for asking this, but roughly speaking about 80 to 95% of problems involving ink or toner are resolved by the following: Are you using a factory new ink cartridge supplied by the manufacturer of the printer? If you are using a refilled or third party cartridge that may well be your problem. Most manufacturers build logic into their products to prevent the use of “Other Equipment Manufactured” cartridges as well as re-filled cartridges. They do this to prevent problems from contaminated inks causing problems with print quality or damaging the physical printhead. Don