Question about Harley Davidson Harley-Davidson Motorcycle Desktop Telephone

2 Answers

Bike wont start

I turn the ignition on lights work radio on but bike wont start is the battery too low it is 5 yrs old or is it a fuse

Posted by millerlite64 on

  • Anonymous Mar 06, 2009

    mine sounded like it would just sping the starter but afterI changed the batery it wont even do that. Lights come on but it wont crank. Not even with a jump start

  • Anonymous Apr 18, 2009

    lights works great, etc. no cranking over - no clicking, no buzzing, etc. NOTHING! Any ideas?

×

Ad

2 Answers

Ryan Rogers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,028 Answers

What is it doing exactly, any clicking, buzzing, any noise at all, or nothing, no sounds at all? Especially in the starter area.

Posted on Aug 13, 2008

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just replaced battery, will click but won't start.

Posted on Oct 04, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 Kawasaki ZX-9R Ninja will not turn over


Test the battery, bike batteries can and do just go open and dead all of a sudden, have been stranded more than once, filled with gas and then no start nothing, no lights nothing.

May 20, 2017 | 1999 kawasaki ZX-9R Ninja

1 Answer

2008 electra glide battery draw, test light pulses, now bike wont crank over


The pulsing could be the alarm module. When bike is turned of, you will get small draw for a minute or so and then it should go very low, below a miliamp or so. This is the alarm module setting itself. Check for this. Is battery gone flat while checks were being made? Make sure ignition switch is on when disconnecting battery if alarm (Stock HD) is fitted. If not, alarm module gets confused and can cause problems. The corrct procedure for disconnecting a battery from an alarm fitted HS is - alarm off, ignition switch on, pull main fuse (Maxi Fuse), disconnect battery. To fit, ignition stitch off, connect battery then install main fuse.

Nov 01, 2013 | Harley Davidson FLHTCUI Electra Glide...

2 Answers

No dash lights , no power , bike won't start. Replaced battery , then regulator last summer(both 5 yrs old) and I finished out the season. Tried to start it during a "warm" spell, but forgot to re


I know this ain't an answer but I'm having an issue with my dash lights I have a 15 softail slim I just put on new apes and the wiring was all plug and play bike was down foe 2 weeks without starting due to waiting on break line but received it today and put everything back together made sure all connectors were plugged in connected battery and and all lights came on even fuel gauge light but no dash lights and it will not start anybody have any suggestions. . I would greatly appreciate it..
thanks..

Mar 25, 2013 | 2007 Harley Davidson FXD Dyna Superglide

1 Answer

2008 yamaha r6 wont start i put in a new ignition now my fuel pump wont ingage and my neutral light wont come on for some reason my bike will not start or turn over what is wrong and how do i fix


Good Morning,. I found this for you.. worth a shot:
  • verify that the main fuse is not blown. It would be inside the starter relay. To locate the starter relay, follow the cable from the battery's + terminal;
  • if the battery and the main fuse checks good, then check the voltage on the red wire from the starter relay to the ignition switch;
  • do the same and check for the presence of +12 to the brown wire from the ignition switch to the CDI.
  • Best regards
  • Ck

Oct 30, 2011 | 2008 Yamaha YZF-R6

1 Answer

1993 suburban is not starting and it is not the battery. What could it be?


IF BATTERY CABLES OLD THEY WILL CAUSE POOR GROUND HIGH RESISTANCE IN STARTER CIRCUIT CAUSING STARTER NOT TO CRANK ENGINE.CHECK TO SEE IF DASH LIGHTS AND GAUGES WORK WHEN YOU TURN ON IGNITION SWITCH IF NO CHECK IGNITION FUSES.IF FUSES OKAY IGNITION SWITCH IS OPEN NEED REPLACING.NOW IF BATTERY VOLTAGE IS 12.6 VOLTS, BATTERY CABLES GOOD AND IGNITION SWITCH AND FUSE OKAY. STARTER SOLENOID OR STARTER FAULTY.REMOVE STARTER TAKE TO ANY AUTO PARTS STORE THEY WILL TEST STARTER.TURN OFF RADIO BEFORE REMOVING NEGATIVE BATTERY SO YOU WONT LOCK OUT RADIO.

Nov 02, 2010 | 1993 Chevrolet Suburban

1 Answer

2003 Honda VTX 1800 will not turn over.


Hi, Tldanie before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike wont turn over Help vtx 1800 2005
Troubleshooting Motorcycle that Wont Start Honda VTX 1800 Partzilla com
Honda VTX1800R Owner Manual service manual, not owners.
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1800R Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jan 30, 2010 | 2003 Honda VTX 1800 Retro Cast

2 Answers

Nothing works and can't remove key from ignition


If the battery is dead, the ignition keys will not come out of the ignition cylinder. Don't force the ignition key to ensure you do not damage the pass lock system in your ignition. Jump the battery or replace it to get enough voltage to remove the key's from the ignition and check the fuse box for any blown fuses. Good luck and keep me posted.

Dec 08, 2009 | 2008 Chevrolet Impala

1 Answer

Bike will not start no power


Touch a 12" piece of wire to one terminal then touch the other end of the wire to the other terminal. Got a really good spark? No spark = bad battery. Okay, so you do get a good spark. Check the wiring harness for an unplugged wire. Also check for loose connections and burned wires. Bad ignition switch? Kill switch turned on?

Mar 13, 2009 | 2005 Honda CBF 500 ABS

Not finding what you are looking for?
Lands Phones Logo

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Lands Phones Experts

Tom Diffin

Level 2 Expert

95 Answers

Steve F

Level 3 Expert

1360 Answers

Mai Lor

Level 3 Expert

2558 Answers

Are you a Harley Davidson Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...