Question about Mitsubishi WD-52725 52". Rear Projection HDTV

1 Answer

Mitsubishi WD-52725 52 in

Timer light started to blink. What could be the problem?

Posted by danrussell63 on

Ad

1 Answer

MICHAEL MULLINS

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 927 Answers

Good Day, danrussell63;

TRY THIS:

1. Red status LED, self-diagnosis error 44, check for open F9A06 on the Power PCB part # 283P128050 on the Power PCB 2. Red lamp LED, self diagnosis error 34. Check for 5-volts DC at J-9 connector pin 1 and 2 on the Engine Driver PCB if missing replace the Power PCB part # 930B921002 3. LED stops blinking after 70 seconds of plug in but will not power on. This model is equipped with a keyboard lock feature, this can be mistaken as a no power condition. To unlock the keyboard press and hold the "menu" button on the front panel for 10 seconds 4. LED stops blinking after 70 seconds of plug in but will not power on. Check for 3.2 volts DC at connector LE pin 3 and 4 on the Control PCB, if low suspect problems with the switches/buttons on the Control PCB part # 935D776001 5. LED stops blinking after 70 seconds of plug in but will not power on. Keyboard is not locked and key inputs at connector LE pin 3 and 4 check good. Suspect the E2P PCB part # 934C121001 6. (LED does not stop blinking after plug in) Disconnect the USB connector from the card reader to the front from the Chassis, if the LED stops blinking after 70 seconds replace the Card Reader part # 299P271010. 7. (LED does not stop blinking after plug in) Disconnecting the USB connector from the Card Reader did not help. Remove connector FC from the FMT PCB and plug the unit in, if the LED stops blinking after 70 seconds with FC removed suspect a problem on the FMT PCB (part # 930B924002), if the LED keeps blinking with connector FC removed suspect a problem on the DM PCB (part # 934C116002). 8. (LED does not stop blinking after plug in) On the DM PCB (part # 934C116002) check C81A2, C81A3, C81B3 and C81B4 (1000 UFD, 16V, 105C), if any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C). See Service Tip VS-78A 9. (LED does not stop blinking after plug in) On the FMT PCB (part # 930B924002) check C8F19, C8F21, C8F22, and C8F27 (16V 1000 UFD 105C), if any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C). i HOPE THIS HELPED, BIG irish. Mitsubishi WD-52725 52 in - back.gif

Posted on Aug 13, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Entrance light on Lift Master garage door opener won't stay on when door is opened ?


Light Feature
Activate the Light Feature
  1. Close the garage door.
  2. Start with the garage door opener lights "ON".
  3. Press and hold the light button for 10 seconds. (Upon pressing the light button, the lights will immediately turn off and come on 10 seconds later.)
Deactivate the Light Feature
  1. Close the garage door.
  2. Start with the garage door opener lights "OFF".
  3. Press and hold the light button for 10 seconds. (Upon pressing the light button, the lights will immediately turn on and go off 10 seconds later.)
Light Timer
Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2 minutes. Press again to turn it off sooner. The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows:
  1. Press and hold the Lock button until the light blinks (about 10 seconds).
  2. A single blink indicates that the timer is reset to 1-1/2 minutes.
  3. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes.
  4. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

Oct 20, 2017 | Building Materials

1 Answer

We have fujitsu inverter plasma airconditioner mpdelastb09ldc ths fan runs but timer light blinks 3 times but outdoor does not start


Hi Rajneel,
I hope this link is of some help to you
Good luck
http://www.climatecenter.co.uk/wcsstore/ClimateCenter/Attachment/downloads/fujitsu-trouble.pdf

Feb 10, 2015 | Fujitsu Heating & Cooling

1 Answer

Standby timer blinks times


There are particular blinks meaning on sony TV. I can give you the problem from your sony tv if you specify or count how times the LED flashed.

Jul 06, 2014 | Sony KV-27S42 27" TV

1 Answer

WHEN I START A.C. ITS OPERATION AND TIMER LIGHTS STARTS BLINKING AND N OT COOLING


Sounds like a pressure switch may have it shut down. It could be the main circuit board but not likely. Its in the control circuit and will need to be troubleshot

Sep 26, 2012 | General Electric Heating & Cooling

1 Answer

I have a Mitsubishi WD-52725 and the timer light continues to blink and I cannot reset it. What can i do to fix this.


1. Timer LED does not stop blinking; suspect the DM PCB part # 934C152001-V28++ 2. Timer LED blinks 70 seconds, pauses then starts blinking again, suspect the E2P PCB part # 935D820001-V28+ 3. LED stops blinking after 70 seconds of plug in but will not power on. This model is equipped with a keyboard lock feature; this can be mistaken as a no power condition.

Feb 17, 2011 | Mitsubishi Televison & Video

1 Answer

The tv starts to come on,then goes of and the


off the sleep,standby timer mode on your TV.. you just check all the timer then turn it off.

Mar 27, 2010 | Televison & Video

1 Answer

Fast Blinking Timer Light


If the timer light blinks at the same rate all the time...then the problem could be fairly serious (the tv won't start up). If the blinks are NOT consistent..then count them...it is an error code for service personnel. Try resetting the tv or plugging it out. Wait. Then plug it back in (resets the tv) and see what happens.

Jun 29, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Blinking timer light will not turn off.


You most likely have a fault in the defelection circuitry that is causing this. A repair is needed, none-the-less....accordianman

Jan 01, 2009 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Timer Light.


according to the book hcm4216w says ti will blink 10 times when turned on then then iluminate when on

Jul 20, 2008 | Samsung HCM4216W 42" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52725 52". Rear Projection HDTV Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76376 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...