Question about Canon PowerShot SD1100 IS Digital Camera

Impossible to reset the camera, it is bloked out with a error message to reset the camera. objectif (focus) stayed out

1 Answer

Veril Gillette

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.
Master
1,126 Answers

Remove the batteries from the camera for a few mInutes and reinstall, that should reset back to normal.

Posted on May 03, 2011

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Panasonic DMC-ZS6 when in camera mode lens comes out and I get the message "Please turn camera off and then on again" when I turn off the lens just stays out.

There is an issue with the camera focus circuit in lens. That is why it is ok when you go into playback mode but negative when the lens is involved.

Aug 25, 2017 | Panasonic Cameras

1 Answer

Error message "turn power off and on again" I did this and it did not work.

From: http://www.sony-asia.com/support/faq/303088

Performing a manual power reset (If your camera does not have reset button and initialize function)

Turn off the camera.
Remove the battery pack.
Remove the button-sized lithium battery.
Allow the camera to remain without power for 30 seconds.
Reinsert the button-sized lithium battery.
Reinsert the battery pack.
Turn on the camera.

Jan 07, 2014 | Sony Dsc-s2000 Cyber-shot Digital Camera...

1 Answer

My Panasonic TZ25 says "System Error - Focus". What should I do?

Panasonic DMC TZ25 compact camera - System Error (Focus)
- Try holding the shutter button while switching on the camera (suggested by Andrea Lock, above). I actually had to try this several times as camera was refusing to reset properly, but after a few goes, lens retracted and camera began to work again. Thanks Andrea.

Feb 21, 2013 | Panasonic Lumix DMC-TZ25 Digital Camera...

1 Answer

Lorsque je demarre ma camera il affiche un message erreur lens

Sacrebleu!
C'est parce que le m?canisme d?licat est endommag? et l'objectif pouvez pas d?placer ou lock en position correcte.

.

Jun 30, 2011 | HP Photosmart M425 Digital Camera

2 Answers

E:61:00 error

E 61 00 Difficult to adjust focus Inspect the lens block focus reset sensor
E 61 10 Zoom operations fault Inspect the lens block zoom reset sensor
E 62 00 Steadyshot function does not work well. Inspect pitch angular velocity sensor
E 62 01 Steadyshot function does not work well. Inspect yaw angular velocity sensor

The simple solution to fix that error message was to the let the lens fully extend and give the lens a good whack. Possibly this error message for this means, that the auto focus motor was past the maximum set point.

This may sound crazy and this has not happened since I did this but here is what I did to get rid of that error message. I have not had that problem since but here was my steps:
· Turn the camera off
· Hold the camera face down over a hard surface (Like you are going to take of your desk) with only about half an inch above the surface.

OR reference the video files below for an alternate method.
· Turn the camera on
· Let the lens extend into the hard surface, don't let it extend all the way. Mine retracted slightly and then tried to extend again (let it extend the second time).
· Lift the camera away from the hard surface and notice that the error message is gone.
· Take pictures of your favorite things.

Here is the first alternate method (AVI format)
Here is the second alternate method (AVI format)

Good luck.

May 03, 2011 | Cameras

2 Answers

E:61:00 on the display

E:61:00 means "Difficult to adjust focus Inspect the lens block focus reset sensor"
The simple solution to fix that error message was to the let the lens fully extend and give the lens a good whack. Possibly this error message for this means, that the auto focus motor was past the maximum set point.
goodluck
and do rate the solution if helped

Dec 06, 2010 | Sony Cyber-Shot DSC-P71 Digital Camera

1 Answer

When I switch on the appareil , the objectif don't go out and I have the error message " error objectif "

Try the procedures in this tip.

Nov 04, 2010 | Pentax Optio 60 Digital Camera

1 Answer

Erreur objectif

that's mean that the problem is inside not in programmation
and you will have to open the camera to solve the problem

Jul 15, 2010 | Optimus DC-5347 Digital Camera

2 Answers

Error message on my Nikon D80

I have the same message r07 on the same camera & lens combination. It is an lens error message that the lense will not focus. You can manually focus the lens in the auto mode and the camera will allow you to take a picture. I have been told it is the MR unit and cost of repair around $135.

May 27, 2010 | Nikon D80 Digital Camera with 18-135mm...

1 Answer

Completely bloked

What I can understand is the camera does not allow you to take any photographs. Recharge the batteries fully and try again. If you still can't get it working, please provide all details like what does the display show, what setting are you using etc.

Feb 06, 2009 | Panasonic Lumix DMC-FZ18K Digital Camera