How do I tune in channels? - JVC AV-32F704 32" TV

You can't just tune the new channels on most Tv You have to tune the whole set, go to settings select D T V and ok. If you have done this and still have missing channels the signal me weak, you may have to buy a high gain aerial.

Hi,
Did you try to manual tune/search the channel? If you are using the autosearch/tune feature and the signal is not strong it will simply skip the channel. Find channel 3 with manual search and then save it. Good luck!

Go in to analogue tuning. Tune just the analogue side of the TV.

you can program the channel manually, just press the menu button in the tv panel. select preset and then manual fine tuning to tuned every channel you want to watch and then save it.to make a manual fine tuning, press manual then select channel you want to tuned and then press vol. up/down button to search right frequency channel.do this process in every channel you want to tuned. hope this can help.

Hi
Before tuning the set to auto tune mode, make sure the antenna or cable, whatever may, connected to its appropriate sockets at the back of the set firmly. To make it autotune:

As new services are broadcast, it will be necessary to

re-tune the television in order to view them.

Auto Tuning will completely re-tune the television

and can be used to update the channel list. It is

recommended that Auto Tuning is run periodically to
ensure that all new services are added. All current

channels and settings, i.e. locked channels, will be
lost.

[1] Select the SETUP from the main menu by using

Up or Down buttons. Press OK and Setup menu
will be displayed.

[2] Select the Installation from the Setup menu

by using Up or Down buttons. Press OK and
Installation menu will be displayed.

]3] Select Automatic Channel Scan from the Installation

menu by using Up or Down buttons and press OK.

A screen will appear warning that previous digital

programmes and settings will be deleted. Select Yes
and press OK to continue with the Auto tuning.

The television will start to search for all available

stations.You must allow the television to complete

the search. When the search is complete the Auto

tuning screen will display the total number of
services found.

* After search is completed for digital channels, a

message asking whether to search for analogue
channels appears on the screen

** Press the OK button to search for analogue

channels. The following menu appears on the screen
for analogue channel search
OK.

CAN YOU TUNE ANY CHANNELS? ARE YOU OFF- AIR, CABLE, SAT BOX?

Switch TV on
Press “MENU” on remote until 3 blue arrows appear
Press “VOLUME” keys to tune up or down (shown on blue bar)
When required programme is tuned, input required Channel number (appears on 2 green lines at top) e.g. 02 or 14
Carry on tuning and allocating channel numbers
Select “MENU” to clear or wait until it clears by itself
Channels should now be tuned to allocated numbers

Here's the link to the full user manual.

Cheers

Rich

http://support.sharp.net.au/downloads/opmanuals/CX51N3om.pdf

Hi i had the same problem but i have sorted mine now. What i was doing wrong was i wasnt tuning in the analoge channels only the freeview digital ones. To do this you need to first turn your tv on. Then press the "source" button, this will bring up a little menu at the top left hand side. When this menu comes up press the "Programme +" button (the one that you use for changing channels near the volume button) press this until you get up to "TV", when T.V is highlighted just wait 3 secs and it will switch over. You will probably get a blue screen with a no signal message (you are now on analogue) when you get this blue screen press the "tune" button. It will automatically start tuning in all of your channels, at first they will be fuzzy but as it works they will become clearer. Your sky channel will also be tuned in. When mine tuned in it didnt tune them in on the right numbers though, bbc2 was on number 1 etc. If you ever need to use a playstation or something it goes into the scart connection at the side of the t.v and you need to press "source" and go up to "scart". To get back onto the digital channels just press "dtv/dvd".
hope i helped!

Sounds like the signal is probably too strong. The TV is not the problem.