Question about Heating & Cooling

1 Answer

A error code E154 appears, then I shut down the unit, and restart, no problem a few minutes, then the error code appears again. have you the solution?

Posted by proteco on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 89 Answers

Hello there, I guess your Running capacitor is leaking already, when you start your aircon it will run after a minute the aircon will stop with errors, because the fan is stop running due to busted capacitor. thanks

Posted on Apr 26, 2011

Testimonial: "thanks I will do so"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We are having xerox 1038 model usa made . we are getting the error u6 when we switch on our machine . so plz suggest us the best possible way to fix up the problem ...`````


U6-1 The main PWB failed checking the ROM.

Shut down and restart the copier. If it appears again U6-1, replace the main PWB.

U6-2 The main PWB failed checking the RAM.

Shut down and restart the copier. If it appears again U6-2, replace the main PWB.

U6-3 and U6-4 The main PWB failed to check the battery MNV (U6-3). Or the main PWB does not properly initialize the NVM (U6-4).

Follow the procedure in the development of memory to initialize the NVM, code 20-96. Shut down and restart the copier.

Jul 20, 2011 | Office Equipment & Supplies

1 Answer

The copier stopped working and Error code E000003-0000 came up. I've shut the machine down and restarted, but error code still comes up.


switch on the machine, press *(additional function) 2and8 together and again *, on screen select copier>function>clear>error>ok. switch off the machine and restart.still problem appears then check fuser unit.

Jan 26, 2011 | Canon imageRUNNER 2200

1 Answer

At power on, displays F61 code and switches off


F61 is an error code.
It will automatically shuts down your unit.
This is very common on your unit.

Try to checked if the fan is working or not.
I have repaired some unit before, this is the caused why f61 appeared.
The symptom is shutting down the unit after a few minute.
If the fan is not working it will shuts off automatically to avoid further damaged to your output I.C. from overheating.

If confirmed that the fan is working then I've suspect that your output I.C./pre-amplifier circuit is faulty.
This is quit technical and need to send to repair shop to isolate the faulty parts.
The output IC of your unit is RSN series and quite expensive.

Pls rate my help.

Thaks for using fixya...

Jan 21, 2011 | Panasonic SC-HT75 System

1 Answer

The unit runs Ok for a few minutes and then shuts down.


Does it do this on just battery power or with an external power source? If on battery poer, then the battery if defective.


- Jim

Jul 20, 2010 | Garmin Nuvi 660 GPS Receiver

1 Answer

[email protected] error code,


F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. Note: You may see a "SUD" error code appear first during this failure. This should change to the F02 error code after a few minutes. Proceed by checking the drain hoses for proper connection and kinks. Unplug unit and disconnect power. Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Reconnect power and plug unit in. If problem has not been corrected, replace the pump.

Oct 10, 2009 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Amcoraire / aos241hx / code p8 / unit shut down will not restart


for all error codes. http://www.digelair.net/pdfs/TECHLIT/MITSUBISHI/MrSlim_P-SERIES_Troubleshooting_TIPS.pdf

Jun 30, 2009 | AmcorAire UCHW-H24AF2 Split System Air...

1 Answer

Full Tank


I had the same error and the tank was not even full. I took the cover off of the unit which consisted of removing 10 screws. The water tank is on the bottom left side. I then removed the float which was a small sensor with a styrofoam float. I removed the float (2 more screws) and moved it up and down. It did not appear to move very smooth but after moving it back and forth a few time it seemed better. I put the float back in ensuring it was at the low point, screwed it back in and then tested the unit. It came on and appears to work fine now. I unplugged again putt the cover back on it has now ran 30 minutes no problems.

Jul 13, 2008 | DeLonghi Pinguino PACL90 Portable Air...

4 Answers

"Cool" mode shuts off


An E1 error is automatically generated after the AC runs for so many hours to remind you to clean the filter. The owners manual says to clean the filter and unplug the unit, then plug unit back in and code will be reset. However, a User review stated that his code was not reset until he followed a fairly simple routine. "Unplug the unit. Hold down the power button and plug back in. Wait to hear a "beep" and then unplug it again. Plug unit in again and it should restart without E1 code."

Aug 03, 2007 | Sharp AF-S85FX Wall/Window Air Conditioner

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3534 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18596 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...