Question about Taylor 7506 Glass Lithium Digital Bathroom Scale

1 Answer

My scale showed Lo, no reading, then I replaced battery, now shows nothing, dead. What do I do next?

Posted by lselenje on

Ad

1 Answer

Lance Hill

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,739 Answers

The Instruction Book for your scale can be found here:

http://www.taylorusa.com/media/IBs/7506_ib.pdf

Sounds like no power. Check for correct battery replacement; may need to verify that your replacement batteyr is still good.

Battery Replacement

1. Use 3 volt CR2032 lithium battery (as installed).

2. Open the battery compartment on the bottom of the scale.

3. Remove the old battery from the compartment.

4. Place the new battery with the "+" sign up into the battery compartment.

5. Replace the battery compartment cover.

Posted on Apr 25, 2011

  • Arla Bennington
    Arla Bennington May 21, 2014

    Already did that. Doesn't work.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model ww66


In the event that the scale battery needs to be replaced, (display shows "Lo"),
open the battery cover on the bottom of the scale and replace the old battery with
a new 3V lithium battery.

Jun 04, 2014 | Conair WW60 Weightwatchers Scale

1 Answer

Model 9114 salter scale shows Lo. I have changed the batteries but it still only shows Lo.


I had the same problem and, suspecting that the metal contacts weren't making proper contact with the batteries, I used a long nosed pliers to gently bend all ten contacts towards to the batteries (there are eight small tabs in the battery compartment, and two on the battery cover). If you don't have a long nosed pliers a small screwdriver should do it if you held the fixed part of each set of contacts so it doesn't detach during the process.
Unfortunately, it worked, but only for one weigh, and then it reverted to "Lo". This happened twice, so I telephoned the Salter Customer Service Helpline (01732 360783) who recommended a reset, which is done by removing the batteries, standing on the scale for 20 seconds, and replacing the batteries. That also only worked for one weigh, so they are looking into it further and I'll post the results here, but in the meantime I hope one of the above solutions will work for others.

Jan 21, 2014 | Salter Stainless Steel Electronic Bathroom...

2 Answers

Scale keeps showing lo no weight


Try taking the battery out and putting it back in, also there should be a small reset button. You will need a toothpick to push the reset button. Allow time for the scale to reset before stepping on it.

Apr 19, 2011 | Homedics Digital Scale

1 Answer

Scale shows "Lo"


just fixed this problem myself. so first i took out the battery then put it back in didn't wait a specific amount of time or anything. i just popped it out blew the inside then put the battery back in. next i switched it to ST from LB stepped on it stepped off it then stepped on it again and it reset. then i put it back to LB and voila it worked again!

Dec 18, 2010 | Taylor 7506 Glass Lithium Digital Bathroom...

1 Answer

Scales showing Lo after battery has been replaced


Anytime you have trouble with a Taylor scale - they have a lifetime replacement warranty. You need to call their 800 number and pay for 1 way shipping and they will send you a new one.

Jun 04, 2009 | Taylor & Digital Scale Lithium Scale

4 Answers

Err 1 message on Taylor Lithium Elec Scale model 7346


This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck.

Thank you for your e-mail. The reboot below may clear the error from
your scale. You may need to do this several times to completely reboot
the system. Please let us know if you have any questions or continue to
display the Error.


1. Remove the battery from the scale
2. Set the scale on the floor without the battery in place.
3. Stand on the scale for 10 seconds (still without the battery)
4. Carefully replace the battery without turning the scale on.
5. Using only one foot, tap the scale or apply just enough pressure to
turn on the display. (It should show dashes or zero's) IMMEDIATELY
REMOVE YOUR FOOT.
6. Let the scale turn off
7. Step on the scale for a weight reading


Regards,


Linda DLT
Consumer Relations
Taylor Precision Products
& Salter Housewares
2220 Entrada del Sol, Suite A
Las Cruces, NM 88001
Toll free - 800-289-0944
866-843-3905
Direct - 575-526-0944 ext 3172

Feb 11, 2009 | Taylor & Digital Scale Lithium Scale

1 Answer

I replaced the batteries in my 7542 scale and it keeps showing err or Lo. What can I do?


have you replaced the batteries with duracell or energizers? I ask this because sometimes when it comes to this type scales using a lower name brand type of battery isnt strong enough for it or there just may be a malfunction in that product. Let me know if this helps and good luck!

Jan 24, 2009 | Taylor & Digital Scale Lithium Scale

Not finding what you are looking for?
Taylor 7506 Glass Lithium Digital Bathroom Scale Logo

1,970 people viewed this question

Ask a Question

Usually answered in minutes!

Top Taylor Health & Beauty Experts

Cindy Wells

Level 3 Expert

6220 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18562 Answers

Are you a Taylor Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...