What are the numbers on the dish cap where is number one two three and four go???

1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140 (talk to a machine)
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.
15.



Dealership Codes
202108
206053
620529

Requirements

The theft lock radio must be in "LOC" mode.

Procedure:

1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

165432 one three and five is to the right hand side of the engine.two four six .is the left hand side .you at the front of the car.on your distributor cap held on with two screws first screw near the bottom above it number 1 then 6 then 5 below the next screw is 4 then 3 then 2.

If you look at the distributor cap from the wires side carefully, you would find either a line mark on one of the outer side of four holes (where the spark plug wires are inserted) or the numbers printed on the top of distributor cap (1,3,4,2). Fix one end of the longest high tension plug wire into number 1 hole or the one marked with a line mark on the distributor cap and the other end on spark plug number 1 (the number 1 plug is toward the pulleys and the belts side, then No 2, No 3 and No 4). While standing in front of right wheel you will see the distributor cap in front of you. The rotor moves clock wise. After you fix the 1st cord, next comes number 3 plug wire. Insert one end of the cord into the next to 1 on the right hand side and press the other side of the cord on spark plug number 3. Next to 3 is the cord number 4 and the last one is number 2.

Check timing on your distrubtor cap, Look for burn spots inside cap,if you see any burn spots replace. This is where i would start first.best of luck.

..............................

Procedure:

01. Turn the ignition ON (The radio displays LOC)

02. Hold down the Radio Presets 2 and 3 buttons for six seconds

03. The radio display changes from LOC to a three-digit number. Write this number down. Don’t take forever, fifteen seconds max before the next step.

04. Press the AM/FM button

05. The radio display changes to another three-digit number. Write this number to the right of the first one.

06. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

07. Call 1 800 537 5140

08. Press 1 then # (pound). You’ll hear “Invalid Code, try again”

09. Press 139010 then # (pound). You will be asked to enter your four or six digit code followed by * (start)

10. Enter the number from STEP 6 then * (star)

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to SEC Your radio is now “un-locked” and usable. The Theft-Deterrent feature is STILL active! If you want to disable it, use the instruction in your Owner’s manual. Use the code from STEP 11 instead of your personal code.

if you dont have the code, the radio has to be removed and a gm dealer can get the code.

note sure what model of car this is but try holding down the mode button for three or four seconds

Turn the ignition ON (The radio displays LOC) 2. Press and hold presets buttons 2 & 3 or 1 & 4 for approximately 10 seconds.
3. The radio display changes from LOC to a three-digit number. Write this number down.
4. Don’t take long, fifteen seconds max before the next step.
5. Press the AM/FM button
6. The radio display changes to another three-digit number. Write this number to the right of the first one.
7. You now have a six or four-digit number, the first three digits are from STEP 3 and the last three digits are from STEP 5
8 If you have a four digit number, it will show all four digits at the same time. Example 4523

do this and let me know the code and i will call gm and get your code in the morning