Question about Intel Motherboard

3 Answers

Motherboard not powering up

This is regardng the below suggestion you gave earlier:
--------------------------------------------------------------
hi this is parveen smsc LPC47M172 IC near ddr ram slots count pins and short pin no 92 and 93 both and the motherboard power on and start giving display this method working 98% only 2% change the smsc PC47M172 ic . when mother not powering up than this smsc chip is faulty .
--------------------------------------------------------------

Instead of shorting these pins on SMSC, can we short the green and black wires in ATX 20/24 pin power connector.

Thanks
Babu

Posted by bobyal on

  • bobyal Sep 21, 2008

    Thank you, Parveen.


    I did implement the solution. However I am not so skilled with soldering, hence used a magnifying glass to closely observe and bend the pins 92 & 93 (with a needle) to touch each other. That did the fix and system is back up in good working state. 


    This is really a great fix, I never believed I could implement his fix successfully. Finally achived it without soldering etc.


    Thanks
    Bob

×

Ad

3 Answers

parveen sharma

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 24 Answers

Hi this is parveen

solutiom for d845gvsr not poweringup only led flashing--

short pin 92 and 93 of smsc LPC47M172 with fine tip soldering iron .
pin 92 is nrsmrst signal that is 3.3v at time of working m/b when this signal is low than motherboard not powering up so we short pin 93 that is standby (3.3v) and motherboard powering up again and working properly this problem doesn,t come again in future. this solution is 98% working 2% chances to change the chip.

Posted on Sep 12, 2008

Ad

virendra

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

No power mosfet in vrm section

Posted on Nov 13, 2012

Ad

Anonymous

Change your Motherboard. ok

Posted on Aug 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Message center number


what is an SMSC number?

Aug 19, 2014 | Cell Phones

1 Answer

Problem sending text messages - Error NO CENTER NUMBER Motorola W220


Here is the procedure, but you will need to call your carrier for the correct SMS center #. I will list a few below for you. Also, if entering the number doesn't solve the issue, you will probably want to get yourself a new SIM card, Here is the procedure:

1.go to your message settings and check the message center number to see if it is correct
2. call to your network operator customer care (if your number is not one of the ones below)
3. request the message center number...
4. note it down
5. go to message settings>message center number
6. insert the number which is noted by you and save it



Here is the SMSC # if you have AT&T:

+13123149810

For other carriers, try this:

On your phone, you can maybe get to this setting by dialing *#*#4636#*#*. We also call this the SMSC.

Lastly, for all of your other phone settings you may want to visit http://motorolasetup.tarsin.com
That site will send you all of the current settings that you need and it sends the settings directly to your phone!

Good luck!!
EJ

Jun 25, 2011 | Cell Phones

1 Answer

Hi , I am unable to send sms from my Nexus one phone. I am able to receive the sms all right. please help.


Hi!
Dialing *#*#4636#*#* AKA *#*#INFO#*#* brings up a troubleshooting/statistics menu page. Dial that and select Phone information and at the bottom you can enter the SMSC (Short Mail Service Center) number. If the phone can receive but not send SMS it could be a carrier outage or issue 90% of the time. Try to update the SMSC number and powercycle the phone and test sending SMS.


Jan 27, 2011 | HTC Nexus One Cell Phone

1 Answer

Compaq IJ600 started to print stopped in the middle and now both green lights are flashing tried restarting computer unplugging printer no luck. Any help greatly appreciated.


Go to the below link for Compaq support regardng your printer. There are manual and driver downloads available which should help you diagnost your problem.

http://h10025.www1.hp.com/ewfrf/wc/product?product=217389&lc=en&cc=us&dlc=en&lang=en&cc=us

I hope that you find this information helpful. If so, please leave positive feedback for me.

Thank You,

Brian

Jan 24, 2010 | Compaq Inkjet IJ600 Printer

1 Answer

Smsc motherboard jumpers setting(compaq presario 5000


no need jumpers, the smsc are being setup in the BIOS, enable it or disabled... go to BIOS Setup

Jun 19, 2009 | HP Compaq Presario 6310US (DA201A#ABA) PC...

1 Answer

Sony ericson P1


probably your smsc number is not correct.

You can find it in 'messages' -> settings
Every provider has its own smsc number. You can aslo check the manual from your phone how to change it. And check your telecom provider website for the smsc number.

B.r.

Sep 01, 2008 | Sony Ericsson P1i

1 Answer

Emachines D845GVSR motherboard repair


your i/o controller ic {SMSC} fail or rtc circuit fail there is two most possibility

Apr 01, 2008 | E-Machines eMachines Desktop PC

2 Answers

Help


See if the latest drivers are installed for the device, by going to Acer's website.
If it is an old laptop and the same was working on the earlier installed operating systems, and now it is not working with new os .. check for the drivers.
And if all of a sudden this happened check for a cable connector which might be right below the keyboard of the laptop. be carefull when you open the keyboard, and just follow the cable from the speakers and you will be able to locate the connector , check whether the connector is loosened of disconnected. Hope your problem will be solved, Cheers-parveen

Feb 10, 2008 | Acer Aspire 5630 Notebook

4 Answers

No power-up only the little green light by the cpu lights up


I tried Parveens solution for this problem on 2 absolutely dead D845GVSR mother boards and it fixed the problem for me on both. On mine you had to permanantly short pins 92 & 93 of the LPC47M172 IC near the ddr ram slots.

There must be a reason for why the motherboard went dead in the first place because from the factory, pins 92 & 93 of this IC are not meant to be shorted. Albeit the motherboards work perfectly the shorting of pins on this IC get over the problem but the original fault is still really there but has been bypassed! Still having said that, what a result!

Feb 02, 2008 | Intel Motherboard

Not finding what you are looking for?
Intel Motherboard Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...