I have a HP Laser Jet P3005. Change cartridge and now just printing out black pages. Put the old cartridge back in and it's fine.

That must be the Lazer assembly has a problem. If you can find a replacement your problem will go. Probably something is blocking it completely.

If you install a cartridge that has previously been installed you will get this warning message. Once you press OK you should be able to print normally. This message is to ensure you do not put the old cartridge in by mistake (yes it happens), or someone does not try to sell you a used cartridge as new.

Unfortunately laser printers don't work this way. The laserjet 1022 was designed for black and white prints only. In order to do color printing with a laser printer you will need to purchase one that is designed to print in color. The laser printers work a bit differently than the inkjets - the laser printers have 4 toner cartridges, one each for Cyan, Magenta, Yellow, and Black, that work together to print a full color page. With the old inkjets you could just replace a black cartridge with a color one.

So, short answer: Sorry but no you can't make a laserjet 1022 print in color. :)

I would recommend looking at an entry level color laser printer from hp, such as the CP2025 (http://h10010.www1.hp.com/wwpc/us/en/sm/WF25a/18972-18972-3328060-15077-236268-3673580.html) if you are looking into purchasing a color laserjet.

Hope this helps

Please rate this post, thanks!

Hewlett Packard P3005 Fuser

Its all about the gears in the fuser drive assembly and the bushing in the fuser.

The HP P3005 fuser is located at the back of the printer.

The fuser has a thin film upper roller which can be torn, some symptons can be "Wrinkled Pages","Poor Fusing", "Toner Rubs Off the Page", "Pieces of black Plastic Come Out".

*** The printer should be unplugged from any power source before any servicing is performed ***

The rear cover can be taken off by removing 2 screws. Once the cover has been removed the fuser can be removed by taking out 4 screws and 3 electrical connections.

Part Number and purchasing link below

RM1-3717-020

This document provides information about replacing the print cartridge for the HP LaserJet 1010 printer series, including life expectancy and replacement instructions. Print cartridge life expectancy The life of the print cartridge depends on the amount of toner that your print jobs require. When printing text on letter/A4-size paper at five percent coverage, the print cartridge lasts an average of 2,000 pages. This assumes that you set the print density to three and disable EconoMode. (These are the default settings.) See Ordering supplies for information on ordering replacement print cartridges. Changing the print cartridge Follow the below instructions to change the print cartridge:

1. Open the print cartridge door, and remove the old print cartridge. See the recycling information inside the print cartridge box. Figure 1: Removing old print cartridge CAUTION: To prevent damage, do not expose the print cartridge to light. Cover it with a piece of paper.
2. Remove the new print cartridge from the packaging, and gently shake it from side to side to distribute the toner evenly inside the cartridge. Figure 2: Gently shaking new print cartridge
3. Pull the tab until all the tape is removed from the print cartridge. Put the tab in the print cartridge box to return for recycling. Figure 3: Removing tape from print cartridge
4. Insert the print cartridge in the printer, making sure that the print cartridge is in position. Close the print cartridge door. Figure 4: Inserting new print cartridge

It is usually dirty and old fuser. It would takes longer time to heat up and also triggering error messages. Try changing that.

Every print job, copy, and fax have the solid black line across the pages. I have changed the drum and the cartridge and even tried cleaning mode. Please help!!! I have a HP Laser Jet 2840 All in One

I had a similar problem, it turned out to be a cheap toner cartridge. Replaced it with an HP cartridge and have had any problem since.

hi,

i think your color ink cartridge is near to empty that's why you are experiencing a pause printing..
try to replace it and try to print again..

rey...

It was the teflon sheet problem just change it
it costs around 6$

Thank u
Take care
bye