Question about Freezers

1 Answer

Samsung water filter rs21 dcns

I have just changed my water filter but i cant find my manual to enable me to take the red warning indicator of the fridge freezer, I would be grateful if you could tell me what i should do to remove the red light. Many Thanks

Posted by Fiona Stableford on

  • Anonymous Mar 30, 2014

    how do you change the water filter cartridge on a baumatic titan 4 fridge freezer

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hold down the "ice type" and "child lock" buttons (bottom button on the left and the right) together for about three seconds. The light will change back to green.

Posted on Oct 12, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After replacing filter, how long before filter light goes off?


Filter indicator : The filter Indicator will be Red when you have used your water filter for 6 months, Reset the indicator (it will be Blue) after replacing the filter by holding the "Alarm/Hold 3 sec for Filter Reset" button for 3 seconds.

The above is how to reset the indicator

Jan 22, 2016 | Samsung RF4267HARS 27 cu.ft. French Door...

1 Answer

Whirlpool freezer display flashing 1


Hi Rachel
For your door to close properly take off the gasket from your fridge and wash it with hot water. It will be softer and stick to the fridge much easier.

Feb 15, 2014 | Whirlpool 10 cu. ft. Chest Freezer...

1 Answer

Hotpoint FZ175G red warning light comes on freezer still freezing after reset light comes on again after a couple of hours


Red light on for High Freezer Temperature Warning
or freezer not cooling, but fridge is and a lot of noise from compressor.
Also, fridge drain hole blocked, water in bottom of fridge.


This is a common fault in Hotpoint Fridge Freezers and can also happen if the door has been left open or has been a power cut.

1. Turn off fridge freezer, or at least turn down the freezer temp to minimum, though not ideal.
2. Open freezer door and remove all drawers.
3. Remove the back panel on the inside of the freezer. This is held in place with 4 screws, which might be 6mm hex head or star allen head. Pull the panel out.
4. Behind where the panel was, there is a cooling element for cooling, pipes, and below this a temperature sensor. If the fridge freezer is not switched off, then fold together a few layers of tinfoil and wrap around the sensor.
5. Use a hairdryer to slowly melt the ice. Melt it around areas where it appears to be hanging on, such as the corners of the cooling element or bolts, as well as any thin sections below the main block of ice around the cooling element, which will be supporting the main block. Use a plastic ice scraper to remove ice but not near pipes or sensor.
Warning: Be careful using electrics around water & melting ice & drips.
6. Below the cooling element, there is a drip channel & drain hole. If this hole is full of ice, pour a small amound of warm water down, leave for 10 seconds and pour a bit more until clear.
In the fridge, clear the drain hole in the same way.
Warning: Do not pour a lot of water down, as this water drains onto a tray above the hot compressor at the rear of the fridge freezer to be evaporated by the heat of the compressor and the tray will only hold a small amount.
7. When all ice is removed, dry all moisture. Put the shelves back. Close door. Turn on fridge freezer. Turn up the freezer temperature to your normal setting. Turn on fast freeze if available. After 1 hour, check with a thermometer. It should be cold enough after 1 or 2 hours.

Sep 17, 2013 | Freezers

1 Answer

Fridgidaire freezer warming up


Red light on for High Freezer Temperature Warning
or freezer not cooling, but fridge is and a lot of noise from compressor.
Also, fridge drain hole blocked, water in bottom of fridge.


This is a common fault in Hotpoint Fridge Freezers and can also happen if the door has been left open or has been a power cut.

1. Turn off fridge freezer, or at least turn down the freezer temp to minimum, though not ideal.
2. Open freezer door and remove all drawers.
3. Remove the back panel on the inside of the freezer. This is held in place with 4 screws, which might be 6mm hex head or star allen head. Pull the panel out.
4. Behind where the panel was, there is a cooling element for cooling, pipes, and below this a temperature sensor. If the fridge freezer is not switched off, then fold together a few layers of tinfoil and wrap around the sensor.
5. Use a hairdryer to slowly melt the ice. Melt it around areas where it appears to be hanging on, such as the corners of the cooling element or bolts, as well as any thin sections below the main block of ice around the cooling element, which will be supporting the main block. Use a plastic ice scraper to remove ice but not near pipes or sensor.
Warning: Be careful using electrics around water & melting ice & drips.
6. Below the cooling element, there is a drip channel & drain hole. If this hole is full of ice, pour a small amound of warm water down, leave for 10 seconds and pour a bit more until clear.
In the fridge, clear the drain hole in the same way.
Warning: Do not pour a lot of water down, as this water drains onto a tray above the hot compressor at the rear of the fridge freezer to be evaporated by the heat of the compressor and the tray will only hold a small amount.
7. When all ice is removed, dry all moisture. Put the shelves back. Close door. Turn on fridge freezer. Turn up the freezer temperature to your normal setting. Turn on fast freeze if available. After 1 hour, check with a thermometer. It should be cold enough after 1 or 2 hours.

Sep 09, 2013 | Freezers

1 Answer

Filter changed but still 1% on display panel


Is this a side by side fridge freezer? Most Whirlpool models with LCD display on front- reset filter indicator to display 99% by pressing and holding 'OK' button until filter resets to 99%. If you have a different model, or of this doesn't work, advise on model number and I can instruct further

Aug 10, 2009 | Whirlpool Freezers

1 Answer

Frost free fridge/freezer - not cold in fridge


The most common problem with refrigerators not cooling when the freezer cooling is the fan which supplies cold air to the freezer. Not easy to get to in most cases. Another problem is the vent to the fridge part is blocked or not operating with the adjustment control.

Nov 27, 2008 | Freezers

1 Answer

Fridge freezer lights flashing


the flashing red light indicates a cooling problem,you should call honest local appliance repair shop(not sears they rob you blind)one other thing to try is to unplug for 5 minutes then plug back in and see if it reset sets itself,could be just a board reset issue,let me know-mike

Jun 10, 2008 | Freezers

1 Answer

Servis fridge freezer


It may be that the temperature of the unit is not yet up to temp.The flashing light will indicate this.Warning the user the unit is not ready,or up to safe temp.. Let the unit run to catch up,since you just started it.

Nov 30, 2007 | Frost Freezer WCWO F15WA FREE - POCKET...

Not finding what you are looking for?
Freezers Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Freezers Experts

Dennis Boxerman

Level 3 Expert

1303 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Are you a Freezer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...