I have a Galilea Moon Phase Clock (Sculptures-Jeux) and cannot find the instructions anymore. How do I set the clock etc. after inserting a new battery. Thanks for help. Marion

Locate the battery: Check the back or bottom of the clock for the door.
Open the compartment: Use a screwdriver or your fingers to open the compartment door. Remove the old battery: Remove the old battery and dispose of it properly

Sounds like the display has aged and is failing.
It looks like there is a version of this clock still being made and sold but branded as La Crosse Technology:
La Crosse Technology WS-8418U-IT Atomic Digital Wall Clock with Moon Phase.
Ordering Information:
https://www.amazon.com/dp/B0016MYATS/ref=cm_sw_em_r_mt_dp_U_hdozDbG1A4Y6B

Hi David,
I am not familiar with this kind of stove, but most of the clocks work the same.

NB, before doing this, unplug the stove.

There is one wire that feeds the clock/timer (this wire is often red). And there is a 0-wire (this one is often blue)
When disconnecting that (red) phase wire, the clock will not run anymore, but neither does the oven.
On the clock must be 1 more wire and that goes to the oven. May be this wire is brown.
Just make a connection with the (red) phase wire and the (brown) wire that goes to the oven.
Then the oven will work again but the clock is out of order.

I hope this helps, Kind regards, Dik

WS 8418AL IT Tomorrow Weather Today by La Crosse Technology

Remove ALL batteries in transmitter AND clock.
Insert new batteries in outdoor transmitter.
Insert new batteries in the (receiver) clock.
Wait until outdoor temperature is received AND displayed on clock BEFORE setting time/date/etc.

I assume you have looked on the Internet to find the manual. Even with all the trillions of things you can find, probably no one has uploaded that manual yet. I had a clock shop for over 30 years. Most grandfather calendar dials can be set by using a NEW pencil eraser. Try to use it near the center of the dial, not on the outside edge. Move the dial clockwise. I suggest a new pencil eraser because a used one can leave smudges on the dial.

-Press SELECT once and time number should flash.
-Press and hold SELECT and it will enter settings mode for the clock.
-At the bottom of the screen next to the moon phase you should now see PST time zone.
-UP and DOWN keys will change the time zone.
-Press SELECT and other clock settings can be changed.

SkyScan 86715:
>Press "SET" once,
>>press "+" until you see your time zone;
-4 ATL-Atlantic
-5 EST-Eastern
-6 CST-Central
-7 MST-Mountain
-8 PST-Pacific
-9 ALA-Alaska
-10
-11
-12
-6MT-?
>Press "SET" once,
DST ON/Off
>Press "SET" once,
US - duh, huh
F - MER-Mercredi, French
E - MIE-Miércoles, Spanish
>Press "SET" once,
>>press "+", for correct hour
>Press "SET" once,
>>press "+", for correct minute
>Press "SET" once,
Range 00-20; 09 = 2009
>Press "SET" once,
Month
>Press "SET" once,
Day
>Press "SET" once,
Day of the Week
>Press "SET" once,
12 or 24 hour
>Press "SET" once,
Fahrenheit or Celsius
>Press "SET" once again - DONE!!!
.
The clock should now display "month/day/day of the week/moon phase/Temperature"
.
NOTE: Moon phase and Seconds will correct on first reception from Coordinated Universal Time (UTC)
.
Lastly,
Press "+" once,
Temperature changes to seconds
>>Press "+" once,
Temperature returns on right-most panel and
seconds replaces day of the week.
>>Press "+" one last time and you are back to done!!!
.
Thanks,
.
[email protected]

-Make sure clock is in radio sync mode. This is in the manual so won't repeat here.
-Press & release SELECT. Clock time numbers should flash
-Press & hold SELECT. It should enter clock settings mode
-Bottom of screen next to moon phase you should see the current time zone. PST after reset
-UP & DOWN will move through time zones.
-Press & release SELECT when done.
-Each time SELECT is pressed will move to a new setting like 12/24 hour etc.
-Press SELECT until clock numbers stop blinking or leave it alone to return to normal mode
-This should also work on the other Oregon Scientific Starck models.

Each time you press the set button on the back it selects one of the items that you can set. For example if the "month" is selected by pressing the "set" button then press the "+" key to change it from 1->2->3->4 etc. Each time you press "+" key the month will go up by one. Stop when you reach the correct month. You can do the same for each item including the time zone and daylight savings time and whether you want your temperature to be in Celcius or Farenheit. Hope this helps...

FixerUpper