Question about Black & Decker ProFinish X750 Iron

1 Answer

My Pro Finish 714 cord was accidentally cut. Is it worth replacing the cord? Where do you get a new cord and can I replace it myself?

Posted by jguiher514 on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 30 Answers

Thank you for using FixYa. Is the cord cut near the iron end or the outlet end? could the cord be shortened? A new cord can be purchased at most reasonable hardware stores and with a little care and attention can be replaced yourself.

Hope this has been of some help.

Posted on Mar 04, 2011


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My iron went nuts and got way to hot. I shut off and the next morning it would not heat up. What to do?

I would say you throw it away and buy a new one. The heating element probably shorted out, overheated and is burned out. Too expensive and not worth the effort to repair.....

Dec 03, 2010 | Black & Decker D2030 Iron

2 Answers

No power from cord. I want to replace the cord.

In replacing the cord, you have to remove the screw that holds the back cover and unscrew the damaged cord from the heater terminal. Insert the new cord on the rubber insulator and screw it to the heater terminal.

Nov 04, 2010 | Euro-Pro Shark GI490 Iron

1 Answer

I have a shortage in my cord and my iron cuts off when the cord moves not all the time but enough to frustrate me. I love my iron. So how do I get it repaired? the shortage is in the top of the cord not...

Take the cord out, cutoff the bad part and reattach...

Here is a tip that will help you to troubleshoot your iron and figure out what is wrong with it.

Electric Iron not Heating Up or not Working Right


May 20, 2010 | Euro-Pro Shark GI490 Iron

1 Answer

How to change the cord of the iron ?

Remove the back plate where the cord attaches to the iron... there are 4 screws visible and another 2 screws hidden under the two rubber feet...These are joined together by a rubber strip and can be removed by prying up and out with a small pry.... once the cover is removed you will see where to take the old cord off and replace it with a new one..

May 23, 2010 | Euro-Pro Shark GI490 Iron

2 Answers

I need to replace the cord on my steam iron. Can i bring it someplace to have it replaced or can i do this myself?

If you can use a screwdriver you can probably do it yourself. Take all the screws out of the handle which should allow you to get to the cord. Determine how they have it attached to your unit. If it is spade lugs there could be a problem. If it is soldered there could be a problem. If they are screwed on we can proceed. Remove the wires and hookup your new cord which could be an old extension cord which is no longer any good. Put your unit back together and you should be good to go.


Thanks for using FixYa and the generous rating.

Mar 04, 2010 | Rowenta DG-980 Iron

1 Answer

Sunbeam iron won't power up.

I bought a new replacement iron at Sears for $17.99. It is not worth fixing my old one .

Jun 17, 2009 | Sunbeam Irons

2 Answers

Broken electrical cord

if the wires aren't bare, wrap them in electrical tape. PLEASE RATE MY ANSWER.

Mar 07, 2009 | Euro-Pro Shark GI475 Iron

1 Answer

Shark euro-pro iron cord replacement model 4750

six screws on bottom plate two hidden under rubber feet on bottom under lower screw holes

Nov 18, 2008 | Euro-Pro Shark GI490 Iron

Not finding what you are looking for?
Black & Decker ProFinish X750 Iron Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Irons Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Brad Brown

Level 3 Expert

18455 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Black & Decker Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides