I have two problems. 1) i cant turn the volume up or down with the side buttons, and im sure that those r the volume keys. 2) i cant recieve the multimedia messages that have been sent to me. i can send them but cant receive them?! What?! please help meee :)

To turn off
Powering down , then back on should do the trick. Be sure to completely down. Do not select "restart". If you still have problems, remove back cover and pull battery from device. Leave the battery out for about 60 seconds, then place the battery back in, assemble the rear cover and start the phone again.
Some galaxy s4 models may require you to press and hold the volume down button during start-up in the same manner as enabling it to exit safe mode.
http://www.technipages.com/samsung-galaxy-s4-turn-safe-mode

1. If your Samsung Galaxy S II is frozen, Shut the POWER OFF, take the battery out and put it back again.
2. Hold the Volume Down button
3. Briefly Press and release the Power button
4. A menu will then appears that let you allows for Fastbook, Recovery, Clear Storage, and Simlock
5. Select Clear Storage by pressing the Volume Down button
6. Quickly Press and release the Power button
7. Select Volume Up for YES and Volume Down for NO

If the above procedures doesn't work. try this another method:

1. Turn the POWER OFF, pull the battery out and put it back again.
2. Simultaneously press the Volume Up, Home and Power button
3. If the Samsung Symbol appears, release the Power button
4. A Boot Menu will then show, Use the volume up/down to choose and home to select.

1. Power down the phone then remove/reinsert the battery to ensure that the device is completely off
2. Press and hold the following keys for 10 seconds: Volume Down + Home Button + Power Button. Release all 3 keys when the Android Recovery Menu pops up
3. Press Volume Down to scroll down and highlight "wipe data/factory reset"
4. Press the Menu Button to select
5. Press Volume Down to scroll down and highlight "Yes - Delete All User Data".
6. Press the Menu Button to select
7. After data wipe is complete simply highlight "reboot system now" and select it by pressing the Menu Button.

Seems like a known issue with the W902. Same here, dropped my w902 a few months back and the Walkman button and Volume up keys not workin now.

Walkman button not really an issue as you still can navigate to it via the menu system but no volume UP key is annoying. You can't increase volume especially when you volume it down. Power the w902 down and up, will reset volume to 6/10.

Solution: I came across a site where you can change volume without the volume up key.

1. Ensure you lock the phone (* and Contact key)

2. While holding down the disconnect button (the one that you switch the phone off) and camera button (on the right side, bottom button), pressing 7 will decrease volume while * key will increase volume.

You need to hold both button for 7 and * to work. Works great for me as I dont have to replace my phone, hope this help.

Ronnie

Here you go. . .(#18 is the button location)
1. Volume mute button with LED indicator
2. Volume scroll zone with up/down LED indicators
3. Integrated microphone
4. RJ-11/modem port
5. Optical drive
6. Media Card Reader
7. 2 USB 2.0 ports
8. HP Fingerprint Sensor
9. Integrated stereo speakers
10. Touchpad with scroll zone
11. Touchpad buttons
12. Hard drive activity / HP 3D DriveGuard LED
13. Battery charging LED
14. Power/standby LED
15. Wireless on/off LED
16. Power button with LED
17. HP Info / HP QuickLook button with LED indicator
18. Wireless on/off button with LED indicator
19. HP Presentation button with LED indicator
20. WLAN antennas (with WLAN option)
21. WWAN antennas (with WWAN option)

To turn the ringer off (or on)
press the conf/ function key,
scroll to "ringer volume" using the up and down arrow keysand press the forward arrow key
press the down arrow key for line 1 and the up arrow key for line 2
select the desired ringer volume by pressing the up and down arrow keys or press the down arrow repeatedly till the screen says "ringer off?"
press the save key (right soft key) you will recieve a conformation beep.
you can exit programming mode by pressing the off key.

There are a few types of override procedures for Kenwood.
Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!
"TRACK UP BUTTON" for 3 seconds.. and youre done.

1. Turn on T.V.
2. Turn volume to zero.
3. With remote - enter 9876.
4. On the menu that appears on the left side of the screen, arrow down to "Backlight".
5. Press the enter key.
6. Press the right arrow key so that the number moves from 81 to 83.
7. Press the menu button twice. The hum is gone

This is the preferred method of code searching our technicians use.

1. TV on.
2. On your Dish Network remote PRESS AND HOLD the small clear tv button until all buttons across the top of the remote light up and release.The only button lit should be the clear tv button that will be flashing.
3. Press the small red tv button next to the power button and release it. This should leave the clear tv button that was flashing lit solid.
4. Now slowly depress the channel up key until the tv turns off.Each time the up channel button is depressed the clear tv button will cease being lit and once it is released the clear tv button should remain solid. If the clear tv button flashes multiple times it usually means there is no known code for your tv, there may be another code that will work so continue on.
5. Once you are successful in getting the TV turned off press the channel down button once and then the channel up button. This should turn the TV back on.
6.Press the # key button on the remote. The clear tv button should flash three times then press the record button and try the volume up/down and the small red tv button. You should be able to turn volume up and down and turn tv on /off. If only one of these function it means that you have only found a half code and need to try the process again. Not all TV's have full codes or any codes at all especially combo units.
I hope this helps you and thanks for using Fix Ya.

Hi Samantha
Try and do a soft reset for your device by pressing the reset button on the side of the device "It's a small hole just below the volume slider. You can press it with your stylus pen"

If that doesnt work, you may need to hard reset the device. Note, if u hard reset, you will loose all your data. Make sure you backup all your data before doing a hard reset.

It can be done by holding down the two soft keys on the front of the phone (the soft keys are two buttons with a "-" symbol on them.

To hard reset,hold down the two soft keys on the front of the phone (the soft keys are two buttons with a "-" symbol on them.

Hold those two down, at the same time, while pressing the reset button on the side of the phone. This will erase all data, and restore the phone back to factory condition.

Cheers