The button continue to blink with top light and fail to print

The Power light and the Resume light blink.

Print media is jammed in the
device.
Remove all media from the output
tray. Locate and clear the jam. For
more information, see Clear a jam
in the device.
The device carriage has stalled.
• Open the top cover and
remove any obstructions
(such as jammed media).
• Press (Resume button) to
continue printing.
• If the error persists, turn the
device off, and then on again

What this light sequence means that the printer has a paper jam.

When a paper jam occurs, the printer stops and the operator panel's Paper Jam light and Continue button lights come on. Press and release Continue twice quickly to display the specific secondary error paper jam light sequence.

How to clear Paper Jam

?· Press Continue button twice quickly to see the secondary error code.

To get the secondary error codes

?· When the Error light (!) and Continue button lights are both on, a secondary error has occurred.

?· When the Paper Jam light (4th light) and Continue button lights are both on, a paper jam secondary error has occurred.

?· Press and release Continue button twice quickly to display the secondary error code light sequence.

Press Continue button to resume printing once all the jammed pages are cleared from the paper path.

We recommend that you clear the entire paper path when a paper jam occurs.

To clear a paper jam:

1 If you are feeding paper from a tray, remove the tray, and then remove any jams.

2 Open the front cover and remove the print cartridge assembly.

NOTE: Do not leave the print cartridge assembly exposed to direct light for an Extended period of time. Extended light exposure can cause print quality problems.

3 Remove any jams in the area behind the print cartridge assembly.

4 Lift the flap at the front of the printer and remove any jams beneath the flap.

5 Open the rear exit and remove any jams.

6 After you have cleared the jams, reinstall the print cartridge assembly, make sure all printer covers and trays are closed, and then press Continue button to resume printing.

NOTE: The printer reprints the pages that caused the paper jam.

If the blinking light is on Toner Low (4th light starting from left), press and release the Continue button (green button) to clear the light sequence and continue processing the print job. If the light is still blinking, the photoconductor is almost full and should be replaced.

For further assistance, please contact Lexmark Technical Support

Issue

The power light and resume light is blinking.

Power light and resume light is blinking Solution one: Press the resume button

Load paper in the paper tray and press the resume button ( ).

Try to print the job. If the issue continues, proceed to the next step.

Solution two: Clear the paper jam

Step one: Clear the jam from the back and top of the product

1. Remove any paper loaded in the output tray.
2. Turn off the product.
3. Push the button on either side of the rear access panel or duplex unit and remove it. Figure 7: Removing the rear access door
4. Locate any jammed paper inside the product and pull it out towards you.
5. If there is no jam, push the latch on the top of the duplex and lower its cover. Figure 8: Lower the product cover
6. If the jam is there, carefully remove any jammed paper and close the cover.
7. Replace the rear access panel or duplex unit.
8. Open the top cover.
9. Check for and remove any jammed paper by gently pulling it out.
10. Make sure that there are no scraps of paper stuck between the rollers.
11. Close the top cover, turn on the product, and resend the print job.

Try to print the job again. If the issue continues, proceed to the next step.

Step three: Service the printer

If you have completed all the steps listed above and are still experiencing a problem, service the product.

Cause

The product might be out of paper or there might be a paper jam.

samsung ml1640 laser red and green light blinking continuously and printing not happening

Please refer below for detailed troubleshooting of the specific condition:

PRINT CARTRIDGE light RESUME light POWER light Blinking Off On Problem

The printer top cover is open, or there may be something wrong with the print cartridge.

Solution

1. Close the printer top cover.
2. If the PRINT CARTRIDGE light continues to blink, continue with the following steps:
   1. Open the top cover. The print cartridge cradle will move and then stop.
   2. Locate the yellow arrow on the top of the print cartridge cradle. The yellow arrow points to a drawing of a cartridge that represents a symptom. Perform the task associated with that symptom.
   3. For a list of symptoms, refer to How to use the cartridge drawings under the top access door on a 900 series Deskjet .

Unplug Power Cord

Hold POWER and RESUME buttons

Plug in Power Cord

Release buttons after the printers starts up

Hold CARTRIDGE and RESUME

Press POWER

Release all buttons after the beeps

Press CARTRIDGE 16 times

Press RESUME

Unplug the Power cord

FINISH

There 3 light on the printer that able to indicate to user when problem occur.

1st button light blink rapidly = the printer may be out of paper, so load more paper and press the 1st button itself to continue. Or may be paper jam is occur, so clear the paper jam and press the 1st button light itself to continue.

If 1st button light blink slowly = mean the cartridge carriers are stuck, so raise the scanner unit and remove any object blocking the path of the cartridge carrier, make sure the cartridge are closed and installed properly, then lift the scanner unit, gently push the scanner support towards the cartridge carriers, and carefully lower the scanner unit until it is completely closed. After that press the 1st button itself to continue.

If 2nd LED light blinking = the color cartridge need to be replaced soon.

If 2nd LED light is ON = the color cartridge need to be replaced immediately.

If 3rd LED light blinking = the black cartridge need to be replaced soon.

If 3rd LED light is ON = the black cartridge need to be replaced immediately.

YBC (/\)

I found this on the HP support site:

The power light is on, and the resume light is blinking.

The printer might be waiting to complete a print job or to receive data from your computer.

Solution

Wait for the printer to finish the current task. The printer is waiting for the ink to dry on freshly printed paper.

Solution

1. Remove the paper with fresh ink.
2. Press the resume button.

The printer might be out of paper.

Solution

1. Load paper in the paper tray.
2. Press the resume button.

The printer might have a paper jam.

Solution

Clear the paper jam. If the resume light continues to blink after the paper jam is cleared,

OR

if the print carriage is stuck or making a grinding noise, then follow these steps.

Solution

1. Lift the top cover of the printer.
2. Turn the printer off and then on again.
3. Unplug the power cable from the back of the printer when the grinding noise starts. Unplug the power cable from the wall outlet.
4. Movethe print carriage toward the middle of the printer (this proceduremight take a couple of tries to get the timing correct).
5. Remove the print cartridges and close the top cover.
6. Plug the power cord into the back of the printer. Plug the power cord into the wall outlet.
7. Open the top cover, reinstall the print cartridges, and then close the top cover.

The printer may be ready to eject banner paper.

Solution

Press the resume button to eject the banner paper.

Same problem starting this week, is there a reset? If so , how?