Question about Inverter KEB COMBIVERT F5

1 Answer

E.up and eoc always occurs,what the problem? - Inverter KEB COMBIVERT F5

Posted by rust0914 on

Ad

1 Answer

mntech1

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    New Friend:

    An expert that has 1 follower.

  • Inverter Expert
  • 120 Answers

E.UP = Under voltage
Check your supply voltage.
E.OC = Over current
Check for shorts between the inverter and motor.

Posted on Nov 26, 2013

  • mohamad ghazal Mar 16, 2015

    I check all function and no short circuit but usually when i start the inverter the alarm lit e.oc1

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Eoc alam


E.OC is an over current error.

The inverter is sensing a short on the U/V/W terminals. This could be a shorted motor, motor leads and an internal short in the inverter.

Disconnect the motor leads from the inverter, and run the inverter as you normally would.

If the E.OC error does not occur the short is external of the inverter.
If the E.OC occurs, then the short is internal to the inverter.

Nov 26, 2013 | Inverter KEB COMBIVERT F5

1 Answer

Frigidaire plef398dca


Hello Bill Robbins - From what you are describing it sounds like a wiring failure or a communication break failure between the power board and UIB has occurred. Error code F5, typically indicates that the EOC will need replacing. A certified technician will need to test the wiring harness between the ESC, UIB and EOC.

Jan 21, 2013 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

I have EnGenius EOC-3220 (EOC3220) i can not reset with my null serial cable please help me


Depending on the serial cable you have, you may need a modem (crossover) adapter between the cable and the EOC-3220. A good diagnostic is the following: with the EOC-3220 unplugged from power, connect your serial cable and make all the proper baud rate etc. settings in your serial communications program. When it is running, plug the EOC-3220 into power. If you don't see any garbage characters appear on your screen when you plug the power in, your comm program is probably not set up properly. If you see garbage characters but they are not immediately followed by good information from the EOC-3220, then you either need a null modem adapter inline, or you have a dead EOC-3220. If you've never communicated successfully with an EOC-3220 before over the serial channel, the only way to know if you have a dead one is to try again with a known-good one.

Aug 12, 2010 | EnGenius EOC-3220 (EOC3220)

1 Answer

My Engenius access point is having problem wth the resettings. when i reset it, it fail to recongnise the default user name and password, but it recognises the default IP address


Assuming you are using the proper serial channel reset procedure, this should not be occurring. If it is occurring, your unit is probably malfunctioning and cannot be corrected.

Aug 05, 2010 | EnGenius EOC-3220 (EOC3220)

1 Answer

GE oven functional code F1 appears.


Hello, I come across this problem quite often, The f1 error code does not always follow that it is a bad EOC (Electronic oven control) This could also be a problem with the touchpad. The way to figure which is bad is turn electric off, access the EOC and pull the wire harness/ribbon tape for the touch pad. Reassemble the range and switch power back on. If you are still getting the F1 it is the EOC..If the F1 clears then your problem is with the Touchpad. If you have any other questions please feel free to comment again. Good Luck!!! Mike

Aug 18, 2009 | GE Kitchen Ranges

1 Answer

F7 error code- what does this mean?


Frigidaire / Westinghouse / Tappan / Gibson
Oven Fault Codes
Display Condition Remedy
F0 & F1 EOC failure Replace EOC
F2 Oven over heat Defective Sensor or EOC
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it
F5 EOC failure Replace EOC
F6 EOC failure Replace EOC
F7 EOC failure Replace EOC

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

May 17, 2009 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

Resetting EnGenius EOC 3610


Dear Venmattey,
please follow these steps, it works:

1. Connect the EOC-3610 to your computer with a null modem serial cable.

2.Start a HyperTerminal session: Click Start and then select Programs-> Accessories -> Communications -> HyperTerminal.

3. After the HyperTerminal window appears:
a. Give this new connection a name. Ex: EOC-3610.
b. Select correct COM port. Ex:COM1.
c.Set baud rate as "38400", data bits "8", parity "none", stop bits "1",and flow control as "None". Then press “OK” to bring up theHyperTerminal window.
d. Unplug the power on the POE injector and wait 5 seconds then plug the power back in.

4. Wait until the "#" is displayed in the HyperTerminal window.

5. Type "flash reset", then hit enter.

6. Type "reboot", then hit enter. After the device reboots, all settings will be at factory default.

NEW: Keenan Systems has written a software that will soft reset the 3610 series back to factory reset. Thisfree software is provided "AS IS" by Keenan Systems and is notsupported or guaranteed by EnGenius Technologies. Use at your own risk.


Be Happy Always

Regards

Dec 03, 2008 | EnGenius Computers & Internet

1 Answer

Error code 065 jjj jjjj jjj 065 (frigidair Model feb398ceb)


2 Failure
Code
Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace F2 Oven too hot Check Bake function F3 Oven temperature sensor open Check oven temperature sensor, 1100 ohms F4 Oven temperature sensor shorted Replace component F5, 6, 7 EOC (Electronic Oven Control) failure Replace component F8 Lock switches Check or Replace component Version 3 Failure
Code
Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control) F2 Oven too hot Likely a bad oven temperature sensor (should read 1100 ohms) Possible bad EOC (Electronic Oven Control) F3 Oven temperature sensor open Replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5 or F6 or F7 EOC (Electronic Oven Control) failure Replace EOC(Electronic Oven Control) Version 4 Failure
Code
Condition Check/Repair F1 Circuit board defective Replace control board F2 1. The oven temp has risen above 665F and the door is not locked or
2. The temp has risen above 965F with the door locked 1. Check oven temp in mode that failure occurred. Replace EOC (Electronic Oven Control) if above limits
2. Check 8-pin connector. Check and replace oven temperature sensor if necessary F3 Oven temperature sensor is open (above 3000 ohms) Check resistance of oven temperature sensor, check for open wiring between oven temperature sensor and control F4 Oven temperature sensor is shorted (below 500 ohms) Check resistance of oven temperature sensor, check for shorted wiring between oven temperature sensor and control F5 Internal watchdog circuit has detected a failure Defective EOC (Electronic Oven Control) F6 Shorted buttons Check push buttons and dome switches on control F8 Logic interrupted (lock motor switch sequence) Check door lock switches and wiring

Nov 18, 2008 | Frigidaire Kitchen Ranges

2 Answers

F 14 Error Message


well first it doesn't matter when the problem occurred warranty is warranty but you can pull the oven out and pull the panel off the top where the eoc is and pull the mylar ribbon out there is a black plastic piece at the base of the ribbon pull it up and pull the ribbon out clean it with a pencil eraser then reseat it and lock it down if that doesn't fix it then the eoc must be replaced go to www.frigidaire.com and find a service in your area it will be a warranty issue

Feb 09, 2008 | Electrolux ICON Designer E30SO75ESS Oven

1 Answer

Config page


You will always use a straight through.moz-screenshot-1.jpg The default IP for this is  192.168.1.1 you also need to setup your PC with TCP\IP in order to log in. Go to network connections and double click on the  connection for the NIC. high light internet protocol TCP\IP and click properties.moz-screenshot-3.jpg then fill this in device IP 192.168.1.1 then  PC IP 192.168.1.10 then 255.255.255.0 then hit OK.  From there go to your browser and type http://192.168.1.1 there is no password or user name set the first time. moz-screenshot-2.jpgmoz-screenshot.jpg

Oct 27, 2007 | EnGenius EOC-3220 (EOC3220)

Not finding what you are looking for?
Inverter KEB COMBIVERT F5 Logo

Related Topics:

894 people viewed this question

Ask a Question

Usually answered in minutes!

Top Inverter Electronics - Others Experts

ray gallant

Level 3 Expert

69278 Answers

Tom Chichester

Level 3 Expert

57389 Answers

Anon

Level 3 Expert

1445 Answers

Are you an Inverter Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...