Question about Schlage Locks & Locksmithing

1 Answer

I can't find the code for my schlage keypad lock. Is there any way to reset my passcode without the original code for the lock

Posted by momsoff on

Ad

1 Answer

Coaltowner

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Posted on Mar 05, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Schlage keyless lock lost 6 digit code and no sticker inside either


You will need to take the keypad look off of your
door and record the 6 digit programming code and the two factory
default PIN codes. You then need to perform the factory reset to
erase any codes and restore the lock back to the factory defaults.
This procedure is outlined, as well as the programming of the device, in the attached instructions.

http://www.factorylocks.com/PDFs/Programming%20Instructions.pdf

Regards,
Leslie
Factorylocks.com
877-345-6257 (877-34-LOCKS)

Jan 13, 2013 | Schlage FE595 Plymouth Electronic Keypad...

1 Answer

Shlage keypad dead bolt unlocks when you press the


Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial?
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Videos for installing and programming can be found on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Scroll down and find them under the heading Electronic Security--Keypad deadbolt 365

Aug 31, 2012 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

Need to find code for Schlage keypad door lock but the sticker behind the plate is unreadable. I do have a key.


I don't believe that you can do without the programming code found on the sticker.Here is the contact info you need for customer service:

Schlage Lock Company
Customer Service Department
2119 E Kansas City Rd
Olathe, KS 66061
United States Customer Support
Warranty & Technical Information: 1.888.805.9837

http://consumer.schlage.com/Service-Support/Pages/ContactUs.aspx
Schlage FAQ: http://consumer.schlage.com/Service-Support/Pages/InstallationTroubleshooting.aspx
http://consumer.schlage.com/Service-Support/Pages/FAQ.aspx

Instructions & Manuals: http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx
I urge you to call and I hope that they can help you. Good luck!

Feb 15, 2012 | Schlage FE595VCAM716ACC Camelot Keypad...

1 Answer

Door will unlock without entering code


"Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial? "
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Feb 15, 2012 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

How to change the passcode on the system


Reprogramming BE 365:

This link will take you to the page you need, to get started:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Then scroll down to this heading on that page:
Electronic Security-Keypad Deadbolt BE365
There's a wealth of info under that heading. You will be able to see a PDF file of the original print instructions, as well as a video of how to install the lock. This is useful because there should be a sticker to be found on the backside of the keypad, with the code number that you need to reprogram the lock. This installation video (second item down) will be useful to allow you to disassemble it and view the sticker. This is also a great time to change the 9-volt battery!
The seventh item under that same header is a video which walks you through how to reprogram the keypad to your new code, using that program code that you found on the backside of the keypad.

Good luck!

Jul 19, 2011 | Schlage BE365-CAM BE365CAM505 Lifetime...

1 Answer

I need to change the batteries and reset the pass code in (2) keyless locks ("Locknetics On Board"). The owner's manuals were never given, and the key (Schlage) override was never used.(No...


How can I program my electronic keypad lock when the instructions with the programming code have been lost?
The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.
This number is the programming code referenced in the information for changing the entry code.

This link will take you to the page that you need to get started:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Then scroll down to this heading on that page:
Electronic Security-Keypad Entry Flex-lock FE595/Keypad Entry Auto-Lock FE575 Documents

There's a wealth of info under that heading. You will be able to see a PDF file of the original print instructions, as well as a video of how to install the lock. This installation video (third item down) will be useful to allow you to disassemble it and view the sticker. This is also a great time to change the 9-volt battery! Batteries should be replace about every three years.
The eighth item under that same header is a video which walks you through how to reprogram the keypad to your new code, using that programming code that you found on the backside of the keypad.
A note about the PDF files: If you cannot view a given file, you need to first install Adobe reader. You can get the free download from here:

http://get.adobe.com/reader/

Good luck--and please provide feedback if this helps!

Jul 06, 2011 | Schlage FE595VCAM716ACC Camelot Keypad...

1 Answer

Do I have to reprogram my lock after changing the battery?


Does the Schlage Keypad Lock or Keypad Deadbolt need to be reprogrammed after changing the battery? The Schlage Keypad Lock and Keypad Deadbolt does not need to be reprogrammed after replacing the battery. All settings are retained in the memory of the lock, including valid user codes and the programming code.

I'm including a link to the pdf file of the complete installation and programming instructions:

http://consumer.schlage.com/Project%20Documents/P515-859.pdf

You may also find more useful information on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx#1

Apr 05, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

How do you reset a code on a Schlage Keyless Lock?


here's a link to the installation instructions, which includes programming instructions:
http://consumer.schlage.com/Project%20Documents/P515-858.pdf

There is more information about your model on this page:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx#13

Jan 13, 2011 | Schlage Lock BE365VCAM716 Electronic...

1 Answer

.how to reset code push


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

There's a video that shows you how.

Good luck!

Nov 20, 2010 | Schlage BE365-CAM BE365CAM505 Lifetime...

Not finding what you are looking for?
Locks & Locksmithing Logo

Related Topics:

5,967 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schlage Locks & Locksmithing Experts

JOHN LAPIER

Level 3 Expert

2601 Answers

Mike

Level 3 Expert

4369 Answers

Cindy Wells

Level 3 Expert

6182 Answers

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...