Toshiba REGZA 52RV530U LCD TV Logo

Question about Toshiba REGZA 52RV530U LCD TV

2 Answers

I can't remove the stand off the tv - Toshiba REGZA 52RV530U LCD TV

Posted by gagan_r on

Ad

2 Answers

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 64 Answers

Hi, i have instruction on removing your base stand.

Removing the Pedestal Stand
1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface.
Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.
2) Remove the jack pack cover on the back of the TV to expose
the pedestal stand screws. The jack pack cover can be removed
without tools.
3) Remove the four screws shown in the diagram below. This will
allow removal of the pedestal stand.
4) Once you have removed all four screws holding the pedestal
stand in place, remove the pedestal stand from the TV by
sliding the pedestal stand away from the TV.

i can't remove the stand - 1hungryghost_3.jpg

Posted on Feb 12, 2011

  • Anjali Pradhan Oct 30, 2011

    Thank you. Its very useful. The Haier TV manual also dont have this instruction.

  • Henry Arrow Oct 10, 2012

    Thanks a lot from for the usefull information a satisfied Swiss Friend of General Johann August Sutter

×

Ad

Kevin West

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

For 17 in CLC507: Remove the cover off the very bottom of the stand by turning upside down and removing 4 small screws, then gently pry the tabs while pulling on the base to remove the stand bottom. Remove the internal screw from the bottom, and remove 3 more screws from the back. Remove stand.
Note: There are no internal bosses or threads to mount a wall mount on the VESA-type 4 -bolt mounting surface, which has 4 rubber plugs in the mounting bolt holes. The entire back and circuit board must be removed to install nuts or bolts and washers from inside the TV to attach a wall mount, unless the same stand bolt-holes are used.

Posted on Dec 30, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How do I remove the stand from my 42lg50 tv

If you mean the original stand, place the TV LCD panel down on a table that is covered with a soft cloth. Look at the bottom center of the back of the TV and remove the 4 Philips head screws. Once the screws are removed, pull the stand away from the TV. The base can be removed from the stand body by removing another 4 screws that are at the top of the stand body.

See page 12 of the user manual available from the LG support page: https://www.lg.com/us/support/product/lg-42LG50.AUS . The current link to the manual is https://gscs-b2c.lge.com/downloadFile?fileId=KROWM000196216.pdf .

I hope this helps. If you have put a third party VESA stand on the 42LG50, you may have to remove the TV from the stand to reach the mounting plate.

Cindy Wells
0helpful
1answer

Remove stand from w4207 TV

Put tv on bed face down and look at the stand and locate and remove any and all screws holding stand to the flat screen set. Then after mounting the wall plate per instructions mount the tv to wall mounting.
1helpful
1answer

I need to remove the stand from my Toshiba 37HL67 so I can mount it on the wall. Can you help me. Auburn [email protected]

Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface.

Note:

Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

2) Remove the jack pack cover on the back of the TV to expose the pedestal stand screws. The jack pack cover can be removed without tools.

3) Remove the five screws shown in the diagram below. This will allow removal of the pedestal stand.

4) Once you have removed all five screws holding the pedestal stand in place, remove the pedestal stand from the TV by sliding the pedestal stand a way from the TV (Remorve 5, 4mm or 5/32" Allen Bolts from back of TV.)

For Mordels
26HL67
32HL67
32HL67U
37HL67 = My TV
42HL67

Herb

0helpful
1answer

Can't remove base from Regza 37HL17

download manual and check' page 5 'for wall mounting.

Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface.

Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.

2) Remove the jack pack cover on the back of the TV to expose
the pedestal stand screws. The jack pack cover can be removed
without tools.

3) Remove the five screws shown in the diagram below. This will
allow removal of the pedestal stand.

4) Once you have removed all five screws holding the pedestal
stand in place, remove the pedestal stand from the TV by
sliding the pedestal stand away from the TV.


Five screws
0helpful
1answer

I just purchased a JVC 47'' LCD just need to know how to remove the stand. I have it hanging on a Unti do not need the stand.

1. remove the 4 screws on the back of the TV (these are located in the deep holes above the stand)

2. after the screws are removed, the TV will lift from the stand.

The stands sits inside the TV. after the screws are removed the TV will still sit on the stand. you (and someone else) will need to lift it from the stand.
4helpful
1answer

Try to mount TV to the wall and need to release the TV stand

To Display your LCD TV using a Wall Bracket:

If you decide to wall mount your LCD TV, always use a ULlisted wall bracket appropriate for the size and weight of the LCD TV: 32HL37/32HL37U/32HL17/32HL17U: 38.6 lbs (17.5 kg)

37HL17: 46.3 lbs (21.0 kg)

42HL17: 59.5 lbs (27.0 kg)
1) CAUTION: Two people are required for installation.

2) Unplug and remove any cables and/or other component connectors from the rear of the TV.

3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.

4) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV as described below.


Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

2) Remove the jack pack cover on the back of the TV to expose the pedestal stand screws. The jack pack cover can be removed without tools.

3) Remove the five screws. This will allow removal of the pedestal stand.

4) Once you have removed all five screws holding the pedestal stand in place, remove the pedestal stand from the TV by sliding the pedestal stand away from the TV.
1helpful
2answers

How to remove tv stand from toshiba 42 inch lcd model 42hl167

Hi,
Remove 5 screws as shown in below image to remove stand of TV.
It is also mentioned in user manual of TV page-5, click Toshiba Support to download a copy, if required.
Thanks.

a556384.jpg
4helpful
4answers

I want to wall mount my 26LB30QD but the stand needs to come off, there is nothing in the instuctions on how to remove the stand, please advise.

With the tv laying flat on to the screen, remove the two screws in the recessed holes. Then remove the two screws above towards the input panel, one under AUDIO-L/AUDIO-R and the one under HDMI-1. The stand should easily slide out.
62helpful
2answers

Taking stand off toshiba regza tv

forget the four holes on the bottom of the stand. Remove the five allen bolts on the back bottom of the tv-not the stand. Yank on stand and metal plate slides out with stand.
2helpful
1answer

Question on toshiba tv - fixya post

Found this on the www.Toshiba.com website. Q. How do you remove the stand?
Models: 26HL37, 26HL47, 32HL17, 37HL17, 42HL17, 32HL37, 26HL67, 32HL67, 37HL67, 42HL167, 42HL67,
47HL167, 52HL167, 42LX177, 46LX177, 52LX177, 57LX177
REF:FAQLCD00078
1. Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface. NOTE: Extreme care should always be used when removing the pedestal
stand to avoid damage to the LCD panel.
2. Remove the jack pack cover on the back of the TV to expose the pedestal stand screws. The jack pack cover can
be removed without tools.
3. Remove the five screws shown in the diagram below. This will allow removal of the pedestal stand.
4. Once you have removed the five screws holding the pedestal stand in place, remove the stand from the TV by
sliding the stand away from the TV. The Toshiba customer service number is 1-800-631-3811. Hope this helps you with your problem.
Not finding what you are looking for?

24,040 views

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76843 Answers

Cindy Wells

Level 3 Expert

6477 Answers

Ekse

Level 3 Expert

13435 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...