Question about Kodak EASYSHARE 5100 All-In-One Printer

1 Answer

The printer works OK but it prints two lines clearly but every third is feint almost half the writing is ommitted

Posted by Anonymous on

  • Anonymous Feb 15, 2011

    how do I run a calibration? I do not have any instruction details of how to do it.

×

Ad

1 Answer

Reparatii PC - Service IT

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,574 Answers

Set the print quality to normal or best.
Clean the printhead
Run a calibration.
The Kodak EasyShare AiO performs a calibration every time you install or replace a printhead. However, you can run a calibration if you are seeing changes in the image quality. Calibration aligns the printheads and performs a nozzle health check to enable high-quality prints.
1 Load the main tray or photo tray with photo paper.
IMPORTANT: If you don't have any photo paper, you can use plain paper, but photo paper is highly recommended for calibrations.
2 Press and hold Photo and Cancel together to make a calibration print.
3 Follow the instructions on the calibration print to calibrate the printer.

Posted on Feb 11, 2011

  • Reparatii PC - Service IT

    Click here to download the kodak easyshare 5100 instructions manual.
    If you don't have a pdf reader installed ...click here to download adobe reader.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a sharp sf2116 copier. when copying i am getting half of the page printed properly but the other half is feint. i have renewed the toner.


problem is not the toner , could be the developer unit stopping at that point when it becomes feint and then no new toner gets to the drum,
OR
it could be the transfer section

Aug 06, 2013 | Sharp SF 2020 Copier

1 Answer

My printer only prints the top half of a page clearly. The bottom half is feint and blurry or missing altogether.


Your inks are gradually drying out. You should have them refilled or replaced. When inks begin to finish up in the cartridge, each time you print, part of ink that has settled at the bottom prints, and if the the material you are printing is sizable the bottom part will come out faint or faded out.

Good luck & God bless!

Nov 23, 2010 | HP Officejet 6310 All-In-One InkJet...

1 Answer

Hi! printing flight boarding passes on Epson


run it through a cleaning mode.

in ctrl panel
select printer and r click go to
properties and then the
maintenance tab.
Run clean
Run Nozzle check

When it prints correctly
ensure you select paper size as A4 and print your pass.

Pleazse rate my help++++Thanks for using Fixya

Jun 04, 2010 | Epson Stylus C46 InkJet Printer

1 Answer

Not getting clear print , parts of lines faint or missed, hard to read copies, seems to be bottom half of line,every 4th line


ink low, dodgy ink, or head is wearing, blocked and cant get enough ink to paper, try with manufactures ink, but more than likly the head is block no easy fix, normally a write off, once in a blue moon after much effort one can clean the print head, total sttrip down and windex or metho the print head once removed but be prepaired to work on it for 1/2 a day, get covered in ink, with a good chance of getting nowhere...I'd try fresh ink then I'd quote you more than its cost..labour intesive..sorry

Nov 07, 2009 | Lexmark X5150 All-In-One InkJet Printer

1 Answer

Printer only printing top half of line


I switched my printer off at the mains and back on and this rectified the problem

Nov 17, 2008 | HP Officejet J5780 All-In-One InkJet...

1 Answer

Every other line prints only bottom half of text.


I have a psc 2355 printer which only prints half of text then the next lines are ok then it repeats only printing half text. I removed my ink cartridge and wiped the ink ports with a tissue heavily moisten with water. Repeated this several times and then gently dried with a tissue. The problem was fixed!!

May 08, 2008 | HP PSC 1610v All-in-One Printer

1 Answer

Printer not lining up and display doesn't work


You can adjust the display contrast by pressing and holding the MENU key for 10 to 20 seconds to modify the LCD contrast level.

Jan 17, 2008 | Datamax M-4208 Thermal Label Printer

2 Answers

Hp photosmart 7960


For Photosmart 7960...
Hit MENU
Select "TOOLS" by hitting OK
Select "Clean Cartridges" by hitting OK
Carefully review printed output for white lines on printed areas
If white lines appear:
Select "SECOND level cleaning" by hitting OK
Carefully review printed output for white lines on printed areas
If white lines appear:
Select "THIRD level cleaning" by hitting OK.

Jan 17, 2008 | HP PhotoSmart 7960 InkJet Printer

Not finding what you are looking for?
Kodak EASYSHARE 5100 All-In-One Printer Logo

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Cindy Wells

Level 3 Expert

6224 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...