Question about Phoenix Gold RSD600.1 400W x 1 Car Amplifier Car Audio Amplifier

1 Answer

I have the Rsd 1200.1 and + - and remote wire are connected good but amp doesnt come on nor does the lights come one either...

Posted by vettconv01 on

Ad

1 Answer

Larry Spears

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Make sure that you have power at the amp; test the power wire at the amp. If there is power at the amp; check for a good ground at the amp.Check for fuses at the amp. If you have power and ground at the amp, the issue may be with the amp.

Posted on Feb 03, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I wired a 1200 watt amp kit with a 2x 12 inch box set. I have checked the fuses and they are fine. There is no power. What do I need to check next.


if the power wire is ran to the battery an none of the fuses are bad , check ur ground wire make shore its get good ground an if thatdont work take apart the amp an see if the wire are connected to where ur power goes an the fuses

Jun 19, 2011 | xXx XA10002 Car Amp

1 Answer

I have a jbl gt series gt5 a3011 amp light on top comes on but the power light doesnt fuses are good everything seems to be connected right and no sound to speakers .


Run a jumper between the power wire and the remote (disconnect the remote wire from the head unit first). If the amp turns on, you got a blown fuse, or other problem with the remote turn on from the head unit.

Jun 18, 2011 | JBL Car Audio & Video

1 Answer

Remote wire doesnt turn off amps. and when driving stereo shuts off and comes back on, or puting truck into drive,reverse,or park,the radio shuts down. not all power the lights stay on and amps stay on i...


it sounds like you either used the wrong wire to connect the ground or the wrong wire to connect to the remote power.

for ground it should go to a clean paint free spot on the body of the car - try using a screw that is already attached to the cars chassis or a metal frame point

for the remote turn on wire try attaching it to the wire for you stereo ( it should be switched properly)

if it is doing what you are saying one of these 2 options should work

good luck!!

if you need more help write back and give me as many specific details as you can

Mar 27, 2011 | Eclipse 5506

1 Answer

My amp blew the 20 amp fuses. Replaced and they blew as soon as the radio kicked in. Took the back off to look for any burnt connections or blown open/expanded capacitors or resistors. It smells like...


Remove all the wires from the amp including the remote turn on wire. Once you do that, after about 30 seconds the amp will reset. Hook the power up first, then the ground then the remote. Turn the unit on and check for power WITHOUT the speakers hooked up. If you get no power by now it's a good chance that the amp is cooked. If you do get power, try hoking up your speakers first on one channel then the other channel and then bridged. If it cuts out or off when you touch the speaker wires to one channel or the other, then that channel is no good. Hope this helps.

Mar 17, 2011 | Kenwood KAC-728S Car Audio Amplifier

2 Answers

Amp keeps blowin the two 30amp fuses on the amp.


Make sure that the speaker wires are wired correct at both the amp and the speakers......otherwise it sounds like the typical death of a power acoustik amp (great amps, but prone to a premature death)

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_aad3edb7dfa380b9

Mar 29, 2009 | Power Acoustik GOTHIC OV2-1200 Car Audio...

1 Answer

Power light on the amp goes on after 5 sec off ultra linear 1200


If you run the remote from the battery you will need a on/off switch. Sounds like the amp is overheating. Also, I don't understand bridge the remote and power. They should be seperate going into the amp.

Dec 23, 2008 | Ultra Linear UL-2200D Car Audio Amplifier

1 Answer

Nitro BMW 484 1200 watt amp.


check fuses and remote wire at the head unit. must have a good ground at amp.

Dec 03, 2008 | Nitro BMW-482 Car Audio Amplifier

2 Answers

Rampage amplifier


The amp is supposed to turn on and off with the head unit. The remote wire on the amp should be connected t othe amp control/power antenna wire of the head unit.

The pop should go away when the remote is being switched on with the head unit.

If the amp is staying on with the key removed, it will drain your battery. You need to re-wire it so you don't get stranded.

Nov 29, 2007 | Audiovox Rampage 1200 Watt Amplifier Car...

1 Answer

1200 watt legacy amp not working right


your amp its protect by releas of [powerout]one this releys is dead you mast chenche

Apr 14, 2007 | Pyle Dryver PLAD213 Car Audio Amplifier

10 Answers

AMP turns ON then turns off


The power antenna wire only supplies 12vdc when the radio is on. When CD or other sources are selected, the power antenna wire goes to 0vdc. The remote turn-on wire provides 12vdc whenever the head-unit is on. If your amps are powered on only when the radio is turned on, I would bet that you have the power antenna wire connected and not the remote turnon wire.

Sep 11, 2006 | Ultra Linear UL-2200D Car Audio Amplifier

Not finding what you are looking for?
Phoenix Gold RSD600.1 400W x 1 Car Amplifier Car Audio Amplifier Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Phoenix Gold Car Audio & Video Experts

Tom Chichester

Level 3 Expert

59195 Answers

FastHarley
FastHarley

Level 3 Expert

751 Answers

brian williams

Level 3 Expert

1864 Answers

Are you a Phoenix Gold Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...