I turn my scanner on and the logo comes on with the 2006 copyright ect.It just stays there,No knobs buttons work or do nothing.or squlech.cant put even in defult mode.BCD-996 scanner.

try putting it in drive first

If yu didn't already try, make sure your setting is not on defrost or defrost floor. This car automatically puts the setting on ac and recirculation. Turn it he setting off defrost and try again

Have a lighter handy (I use one of the elongated ones for caravaners)
in-between the burners is a pilot light (top right) keep the lighter flame where the gas comes out.
On the right hand side of the fryer at the bottom is a gas valve with a little black knob.
Press and hold the black knob in and gas will come out of the pilot light and ignite by the lighter flame. You need to hold the button in for quite a while. (until it stays lit)
When it stays lit depress the little black knob and turn it anti clockwise. Gas comes out of the burners and ignites from the pilot light. When it reaches temp. it will cut out.
To turn it off turn the little black knob clockwise. To turn the pilot light off, push and turn clockwise.

It means Electronically Controlled Transmission.

Basically in the older models there is an option to turn ECT on which allows for better acceleration as it's controlled electronically

You may have pressed a button which is labeled "ECT" perhaps near the shift knob or could be somewhere near the dashboard as well.

It's nothing to worry about, unless the light indicates that ECT is not working.

Hope help with this (remember rated this help).

when the logo comes on, press the "tab" key. It should turn the logo off and show you what the computer is doing. This may help:

THIS IS FOR HP AND COMPAQ USERS (it might help others as well)
i had the same problem with my compaq preasrio v6000.
ALL U HAVE TO DO IS
1- START UP UP UR COMPUTER AND PRESS F10
2-GO TO DIAGNOSTICS
3-RUN A HARD DISK TEST
IF IT PASSES THEN YOU JUST NEED TO RE-INSTALL TO YOUR OPERATING SYSTEM
IF NOT YOU WILL HAVE TO CHANGE YOUR HARD DISK.

Or try this:
Go into the BIOS.. Go into the BOOT options.. and hit Shift+1 to disable the Realtek boot option.. pop in the disk you want to boot from.. and make sure you set your boot options to CD-Rom and then HDD.. and just wait.. be patient.. and the blue screen (for booting) will show up! :)

Try performing a "hard reset"

Press and hold the home button (round one on the front)
Press and hold the power button (on top of the phone) so you are now holding both buttons.

If the "Slide to power-off" comes up, ignore it and continue to hold both buttons for 5 seconds.

Keep holding until the phone fades to black.

Wait 5 seconds, then press the power button until the Apple logo appears.


That should reset your iPhone.

If the weather band is working, the scanner should be working. To verify operation:

- Move the MODE switch to "Scanner" and power the unit ON.
- Press the SVC button (chrome button below display).
- Press POL (chrome button below display).
- Turn the SQUELCH knob towards the left until scanning stops and you hear a hissing noise.
- Turn the SQUELCH knob towards the right slowly until scanning resumes.

If the scanner stops on anything - even noise, it's working.

To Program:

- Slide the MODE key to "Scanner."
- Power the unit ON
- Turn the SQUELCH knob to the left until you hear a hissing noise, then turn it the right - slowly - until scanning resumes.
- Press HOLD.
- Press E (PGM).
- Press 0, 1.
- Press HOLD.
- Enter your first frequency, including the decimal point (EX: 156.055).
- Press the E (PGM) key.
- Press the UP arrow (above the SCAN key). Scanner will move to channel 02.
- Enter your second frequency, including the decimal point.
- Press the E (PGM) key.

You should now have two frequencies programmed. Press the SCAN key . . .

If it still will not accept programming, let me know.

BillB

We are having the same problem! Whats the solution!!!?!?!?!?!!!?

Here are the steps to reset the iPhone. You probably performed the first reset, try the other resets.:



If iPhone won't turn on, or the display freezes or doesn't respond

1. Press and hold the Home button for at least six seconds, until the application you were using quits.
2. If that doesn't work, turn iPhone off and turn it on again. Press and hold the Sleep/Wake button on top of iPhone for a few seconds until a red slider appears, and then slide the slider. Then press and hold the Sleep/Wake button until the Apple logo appears.
3. If that doesn't work, reset iPhone. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears

More resets:
Try This:
1. Remove Sim Card
2. Hold in 'Home' button and 'On/Off' button together until Apple logo appears
3. Replace Sim Card
4. Hold in 'Home' button and 'On/Off' button together until normal phone screen appears.


Also, Try this:
1.) Shut down the iPhone 3G.
2.) Start up iTunes
3.) Hold down HOME button on the iPhone 3G
4.) While keeping the HOME button depressed, plug in the Sync cable
5.) A message will pop up to ask if you want to reset.
6.) Just click YES and the reset process should start.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi, Is you CB gear grounded to an "earth" ground? Also try moving the scanner around, away from the CB coax, as your probably getting stray RF from there. I've run 100watt with my scanner 5ft. away from it and no problems for the last 6 years,,
You are using good quality coax, aren't you? Cheap coax leaks like a soaker hose. Hope this helps you,, Mechanic
** and preaching about ham radio does not solve this persons problem!**