Question about Garmin iQue 3600 GPS Receiver

1 Answer

Garmin iQue 3600 GPS Receiver

How do you take off the screen cover to replace?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are 4 torx screws in the back, they need to be taken off and then the case unsnaps, and wala you have it apart.

Posted on Jan 10, 2009

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
issikiki

Naajiyah Auladin

  • 563 Answers

SOURCE: Garmin iQue 3600 "Service" manual.

Hello.
You can find the garmin manual here.
Just type in your unit details.

Posted on Aug 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lcd replace


You should the installation instructions with the new lcd screen



Replacing a damaged laptop LCD screen can bring your laptop back to life.

You'll be able to access files you thought were lost and use the laptop just as you did before. And it's not as difficult as you might think.


Turn off the power, unplug the battery and all cables.

Eject the installed battery if you have one.

This will protect you against electric shock.


Find the small, round rubber screw covers and pry them off.

This will expose the small screws holding the LCD screen frame in place.


Depending on your laptop, these covers might be made of some other type of material.

Remove the frame by gently prying.


Locate the LCD screen's cable and power supply cords. Unplug them and remove any tape holding the screen in place.


Check the identify of the manufacturer on the back or side of the screen.

It may be different than your computer's manufacturer.


Since these screens look so similar, make sure you order an LCD screen that matches your manufacturer's model number, or else the new screen will not fit.


Plug in the new LCD screen, replace any tape holding the screen in place and replace the frame.

Don't pinch any wires as you press the frame back into place.


Screw the frame down and switch on the power to see if it works.

If it does, go ahead and replace the screw covers.


If it doesn't, remove the battery, the screws and the frame.

Check your connections.


If it still doesn't work, call your parts supplier and ask for assistance in getting another replacement LCD screen.


Hope this helps


http://www.laptopscreen.com/
watch video

Nov 04, 2012 | Computers & Internet

1 Answer

Why is my ipod 4g screen blank


is it an ipod nano ?

Remove the two screws on the panel on top of the Nano and remove the top panel.


Use a case opener tool to pop the plastic screen cover off the unit.


Slide the screen up to expose the orange ribbon cable on the bottom of the screen that connects to the motherboard.


Unplug the orange ribbon cable from its port and slide the screen out of the Nano.


Fit a new screen in the Nano and plug the ribbon cable into the port.


Replace the screen cover and top panel of the Nano.


hope this helps

http://www.bing.com/videos/search?q=how+to+replace+an+ipod+4g+screen&qpvt=how+to+replace+an+ipod+4g+screen&FORM=VDRE

Sep 29, 2012 | Audio Players & Recorders

1 Answer

Screen is non-functional and irreparable


Turn off the power, unplug the battery and all cables.

Eject the installed battery if you have one.

This will protect you against electric shock.


Find the small, round rubber screw covers and pry them off.

This will expose the small screws holding the LCD screen frame in place.


Depending on your laptop, these covers might be made of some other type of material.

Remove the frame by gently prying.


Locate the LCD screen's cable and power supply cords. Unplug them and remove any tape holding the screen in place.


Check the identify of the manufacturer on the back or side of the screen.

It may be different than your computer's manufacturer.


Since these screens look so similar, make sure you order an LCD screen that matches your manufacturer's model number, or else the new screen will not fit.


Plug in the new LCD screen, replace any tape holding the screen in place and replace the frame.

Don't pinch any wires as you press the frame back into place.


Screw the frame down and switch on the power to see if it works.

If it does, go ahead and replace the screw covers.


If it doesn't, remove the battery, the screws and the frame.

Check your connections.


If it still doesn't work, call your parts supplier and ask for assistance in getting another replacement LCD screen.



hope this helps

Sep 17, 2012 | Computers & Internet

1 Answer

Replacing Oil pump in Ford Expedition


the oil pump is on the crank behind the balancer and timing chain cover:


REMOVAL

1. Remove the timing chain.
2. Remove the oil pan.
3. Remove the three (A) oil pump screen and cover bolts and the (B) oil pump screen and cover.
4. Remove the two oil pump bolts and the oil pump.

INSTALLATION

1. Clean and inspect the mating surfaces.
2. Install the oil pump and loosely install the two oil pump bolts.
3. Install the oil pump screen and cover and install the three oil pump screen and cover bolts.
4. Install the timing chains.
5. Install the oil pan.

Apr 25, 2012 | 2003 Ford Expedition

1 Answer

How to replace LCD screen


Hello,

To replace the the LCD screen of your laptop, You need to be very careful in replacing this screen. Please kindly follow the steps below to be able to guide You in replacing the screen.
  1. Shut down the Acer laptop, unplug the AC power adapter and all extensive devices.
  2. Remove the battery pack from the battery tray that is at the bottom of the screen.
  3. Open the display panel as far as You can open it.
  4. Pry the rubber screw covers from the display panel's front cover with a small, flat-head screwdriver.
  5. The front panel is the front plastic piece covering the LCD screen.
  6. Remove the Phillips-head screws fastening the front cover to the display panel.
  7. Remove the front cover from the laptop with your fingers.
  8. Remove the Phillips-head screws from each side of the LCD screen that fasten the screen to its metal frame inside the display panel.
  9. Tilt the screen forward, then disconnect the large ribbon cable from the connector on the back side of the screen.
  10. Peel away any tape securing the cable in place. Lift the screen out of the display panel.
  11. Place the new screen inside the display panel.
  12. Reconnect the LCD ribbon cable to the back of the new screen.
  13. Align the screw holes on each side of the screen with the screw holes on the metal framing inside the display panel.
  14. Replace the LCD screen's retaining screws.
  15. Replace the display panel's front cover, and its retaining Phillips-head screws.
  16. Then replace the rubber screw covers.
  17. Replace the battery pack, then reconnect all cables and devices to the laptop.
That is how to replace the screen of your phone.
Hope this was helpful. Thank You for using FixYa!!

Jan 12, 2011 | Acer Extensa 5620 Notebook PC

1 Answer

How do you replace the screen on a Sony VGN-FW290


What you need is a copy of your service manual. This has the details on repairing , disassemble and full instructions to do so.

unfortunately the only one i could find is one you have to pay for
http://www.user-guides.co.uk/download/sony/sonyvaio/sony-vaio-vgn-cs215j-laptop-drive-loud.html

i dont have any pictures but the steps are outlined as follows.

1.) remove laptop hinges cover (the plastic thing that covers the hinges between the computer and the screen, the screen lifts on it).
2.) remove the screw hiders ( small circular plugs covering the screws holding the shield over the display unit)
3.) unscrew and unjack display screen.
.4) replace screen
5.) screw screen in place, replace lid, screw in place, replace screw plugs, replace hinge covers.

Thats it in a nut shell.

Mar 01, 2010 | Sony VAIO VGN-CS215J/W Notebook

1 Answer

Have a acer 4730Z and the lens cover on screen frame is scratched. can the screen frame be removed to replace cam cover...crystal lite


Hi,

No this is not possible to remove an replace the screen frame only. you have to replace complete screen in service center.

Regards

Ashly

Feb 02, 2010 | Acer Computers & Internet

2 Answers

Broken screen on Blackberry Curve needs to be


you can use warranty or send it to the company and they will charge you if you hadnt taooken the warranty

Sep 12, 2009 | RIM BlackBerry Curve 8310 Smartphone

1 Answer

How do I change the print head on a Xerox 8500?


Hi there,

How to remove a printhead
  1. Press the on-line / off-line key on the printer operator panel to set the printer off-line.
  2. Use the upper softkeys to scroll to the 'Replace printhead' card
  3. Press the softkey below the 'Replace printhead' card to enter the wizard.
    An introduction screen displays the message 'Use this wizard to replace printheads. A roll is needed for calibration.'
  4. Press the key for 'Next'.
    The screen displays the message 'Select roll to use'.
    The system does a calibration at the end of the wizard. You can only calibrate on the defined media types. When calibration is not possible with the media available on the printer, the system asks you to load the correct media. When calibration is possible with one of the rolls, the system automatically uses the correct media roll. When calibration is possible with both rolls, use the lower softkeys to select the roll to use.
  5. Press the key for 'Next'.
    The screen displays the message 'Carriage moving to centre position...' while the carriage moves to the centre.
    The screen displays 'Open top cover.'
  6. Open the top cover. The screen displays the message 'Replace printheads' and the printheads that you must replace. Find the correct printhead number on the printhead carriage.
  7. Press the front of the printhead cover to unlock the cover.
  8. Open the printhead cover.
  9. Pull out the printhead and remove it.
How to place a printhead
  1. Remove the protective tape from the new printhead.
    Do not touch the contact and nozzle areas of the printhead after you remove the protective tape.
  2. Place the new printhead in the printhead holder.
    The printhead only fits in one way.
  3. Close the printhead cover.
  4. After you replaced the defective printhead, press the softkey for 'Next'
  5. The screen displays the message 'Make sure that all head covers are properly positioned.'
    Press the key for 'Done'.
    The screen displays the message 'Close top cover.'
  6. Close the top cover.
    The screen displays the message 'Carriage moving to home position...'
  7. The screen displays 'Calibrating...'.
    The calibration process takes several minutes.
    You can stop the calibration process at any time. Press the key for 'Cancel' to stop the calibration process.

Regards,

Anirban Mazumdar
http://www.ikarmatech.com

Sep 08, 2009 | Xerox Phaser 8550DX Laser Printer

1 Answer

Replacing top back cover to Lcd


In front of the screen you should see little rubber contact pieces shoild be about 4- 6 remove these and underneath are the screws to remove housing.
Inside you will see how lcd screen is attached.
Remove lcd screen then replace what you need to. This is the same for most laptops and I would just google your model # tofind out exactly how to.

May 27, 2009 | Dell Vostro 1500 Notebook

Not finding what you are looking for?
Garmin iQue 3600 GPS Receiver Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garmin GPS Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

John Egan
John Egan

Level 2 Expert

85 Answers

Are you a Garmin GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...