We have a Dayton Relay, Time Off Delay model # 6A857. We are using a driveway bell to activate the time delay, we want to delay a 10 watt water solenoid water vaulve can you give us instruction/ diagram how to wire this device?

Yes. You only have to identify the C,NO and NC wires on the motion detector and connect them to the timer.

Open following link for drawings showing Dayton timer wiring.
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Open following link to identify timer:
http://www.grainger.com/Grainger/wwg/search.shtml?searchQuery=1EGD1&op=search&Ntt=1EGD1&N=0&sst=subset

This is typical 8 pin delay timer relay.
The wiring diagram appears on side of the timer.
Open following link for example how to wire 8-pin timer.
http://waterheatertimer.org/images/Connect-relay-to-timer.jpg

Example shows 24Volt, but 120Volt wires exactly the same.
The timer is 120Volts. So connect power to terminals 2 and 7.
Other terminals are dry, and receive no power when 120V is connected to 2 and 7.
In the example wiring, the objective is to have power connected to Load at all times except when timer activates. So power is connected to terminal 1 and Load wire is connected to terminal 6.
If the objective was to have power connected to Load only when timer turns ON, then connect power to terminal 1 and connect Load wire to terminal 3.

Read how to wire timer:
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html#pin

You want 3 minute 'off delay' timer.
When timer is energized with push button or momentary electrical signal, circuit remains ON for set amount of time, and then turns OFF.
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html
Aug 15, 2011 Dayton/ Grainger website is offline

Most delay timers have 1 amp capacity rating, so circuit needs fast acting 1 amp fuse, and timer controls separate relay or contactor unless Load is equal to 100 watt light bulb.

3-minute off delay pin timer
Omron shows 120Volt 8-pin M-series-(minute) 3 minute delay timer
Part number H3CR-H8L 120volt M
http://waterheatertimer.org/pdf/Omron-timers.pdf

Example 240Volt timer showing timer and base.
http://www.sourcingmap.com/ah33-220v-030-minutes-delay-timer-relay-socket-p-119441.html
Wiring diagram shows on side of timer.

1) Dayton 6A855 time delay pin timer
http://www.grainger.com/Grainger/wwg/search.shtml?searchQuery=dayton+6A855&op=search&Ntt=dayton+6A855&N=0&sst=subset
Grainger owns Dayton, so you might want to contact Grainger
http://www.grainger.com/Grainger/static/help_contactus.html
1-888-361-8649

2) Time delay timers at Grainger:
http://www.grainger.com/Grainger/wwg/search.shtml?searchQuery=dayton+timer&op=search&Ntt=dayton+timer&N=0&sst=subset

3) Grainger shows time-delay 8-pin 120 or 240V
http://www.grainger.com/Grainger/DAYTON-Relay-1EJN7?Pid=search
Grainger shows 11-pin 120 or 240V
http://www.grainger.com/Grainger/DAYTON-Relay-1EJN6?Pid=search

Searching for "11 pin 240Volt delay timer" turned up results:

4) Following pdf shows knob-adjustable 240V delay-on pin timer
https://www.relayspec.com/specs/020050/T1Series.pdf

5) Signaline has delay timers (800) 862-2875

6) SSAC
http://www.ssac.com/standard/ff-tdr1.htm

7) Another pdf with 240V delay pin timers
http://www.askco.com/pdfs/tdd_tud_data.pdf

8) Not wanting to say what already know, but each 240V circuit is made from two out-of-phase 120V lines. Any 240Volt Load can be turned OFF by turning off one of the 120V lines. In this way, the Dayton 120V timer can be used to control 240V load.
Also the 120V Dayton can operate 120V double-pole contactor, and then the contactor controls 240V Load.
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html#contactor

Estoy usando traductor Google para responder a su pregunta.
http://translate.google.com/#

Modelo 60X603 nada

Dayton Modelo 6X603
http://www.drillspot.com/products/43240/Dayton_6X603_Time_Delay_Relay
http://www.premiumplc.com/servlet/the-13605/NEW-DAYTON-6X603F-SOLID/Detail
http://www.thefind.com/appliances/info-solid-state-time-delay-relay

Empresa de Dayton es propiedad de Grainger
http://www.grainger.com/Grainger/wwg/search.shtml?searchQuery=daton+solid+state+timer&op=search&Ntt=daton+solid+state+timer&N=0&sst=subset

http://www.grainger.com/Grainger/static/help_contactus.html
Tel?fono de Grainger
1-800-323-0620

1) Pex supply sell the E502 OFF delay Paragon product: Timing cycle begins when switch is activated, and shuts down at end of timing cycle. 5 seconds to 3 hours
http://www.pexsupply.com/Paragon-E502-Electronic-Off-Delay-Timer-5-sec-to-3-Hrs

http://www.grainger.com/Grainger/cycle-timers/timers/electrical/ecatalog/N-8hb

See manuals for Paragon product:
http://waterheatertimer.org/Paragon-timers-and-manuals.html#percentage

2) Tork ACT120 cycle timer (minimum ON is 30 seconds)
http://www.grainger.com/Grainger/TORK-Adjustable-Cycle-Timer-4JNH8?Pid=search

http://www.nsi-sales.com/act_series.htm

See ACT manuals:
http://waterheatertimer.org/Tork-timers-and-manuals.html#cycle

3) Intermatic CT1000 cycle timer: cycle durations of 30 seconds to 30 minutes, with on-off durations from 1 minute to 29 minutes.
Click model number to access manual
http://www.intermatic.com/products/timers/mechanical%20time%20switches/percentage%20cycle%20timers.aspx
Drillspot sells indoor/outdoor 120V or 240V CT1000
http://www.drillspot.com/products/1325934/Cycle_Timer_CT1000_Cycle_Timer?s=1

4) Do a google search for 'electronic cycle timer' or 'percentage timer'

5) Timers listed above can be wired to a contactor (or relay) that turns on auger, if that's what project calls for.
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html
Dayton off-delay timers require push-button operation

Following page has Dayton timer wiring:
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html

Terminals 6 and 7 are wired with 120Volt power as shown.
The push button gives momentary impulse of electricity to timer.
Timer activates when impulse of electricity ends.
Timer activation turns Load ON and begins countdown.
When countdown expires, timer turns Load OFF.

Terminal 2 is 125V Hot from breaker.
Terminal 3 is Neutral.

Terminal 1 goes to Load.
Load cannot exceed 1 amp.
So Dayton timer can only control single 100 watt light bulb, or it can control 120Volt coil on contactor.
Contactor turns on Load with any voltage: 120, 240, 277, etc or 3 phase contactor.


Suggest busman in-line 1 amp fuse between terminal 1 and Load to protect timer.

http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html

You are correct.
#3 is Neutral from breaker
#2 is 120Volt Hot from breaker
#1 is Black wire to load
#6 and #7 are activated with a push button

When activation takes place, the timer turns on power to the load
The timer begins a countdown
The load cannot exceed 1 amp
Power to the load remains ON until the timer countdown is finished

If you have ordinary switch instead of a push button, then you turn on the switch, and timer countdown begins after you turn the switch off.

Open following link for illustrations showing how to wire 8 and 11 pin off-delay timers:
http://waterheatertimer.org/How-to-wire-Dayton-Off-Delay-Timer.html#pin

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7