Question about SMC TigerSwitch SMC8612T

1 Answer

Connect two tigerswitch 6724AL2 via fiber port

Posted by varga_ioan on

Ad

1 Answer

Doctor PC

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • SMC Master
  • 7,733 Answers

How do I open ports in the Virtual Server? connect two tigerswitch 6724AL2 via fiber port - pix.gif pix.gif You need to forward the ports used by the application to the server running the application in the Virtual Server, which is present in the router's management screen, as follows.

  1. Open your web browser, type in the router's IP address (standard: 'http://192.168.2.1') and press enter.
  2. Click on Login, Advanced Setup, NAT, Virtual Server.
  3. Enter the port details and enable it as follows:
Private IP Private Port Type Public Port 192.168.2.x xxx TCP xxx 192.168.2.x xxx UDP xxx To access the application, you can open up the ports specific to the application in the special application, which is present in the router management screen as follows:
  1. Open your web browser, type in the router's IP address (standard: 'http://192.168.2.1') and press enter.
  2. Click on Login, Advanced Setup, NAT, Special Application.
  3. Enter the port details and enable it as follows:
Trigger Port Trigger Type Public Port Public Type Enabled 3724 TCP 3724 TCP Y 6112 TCP 6112 TCP Y 6881 TCP 6881-6999 TCP Y
* The port numbers given are just an example. You need to open the ports depending on the application you are using and should get the information from the application provider.

Posted on Jan 05, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
3answers
0helpful
1answer

HOW DO I RESET A SMC 10/100 TO FACTORY DEFULT

Remove the power cord from the back of the switch.
Remove all cables from the front panel ports.
Connect port 1 to port 2 on the front panel using a standard patch cable.
Reconnect power to the switch.
Wait at least 40 seconds before disconnecting the patch cable between port 1 and port 2.
After the above is completed, the password will be "smcadmin" and the switch IP will revert to 192.168.2.10
0helpful
1answer

Everyday I need to reboot SMC8024L as systems not getting IP address from stand alone DHCP server could you please suggest what needs to be done here ??

The lease time on DHCP IPs is usaully set for 24 hrs. Try assigning a static IP or changing the lease time. These settinbg are located in router.
0helpful
1answer

I have a problem with 2 smc tigerswitch 6724Al2 to connect them via fiber port

You can take a look at the installation guide and check the guideline about optic connection there if you didn't. If LED light up then you might need to check something on the second document on troubleshooting part.

http://www.smc.com/files/AB/MN_6724AL2_INS.pdf

http://www.smc.com/files/AU/MN_6724AL2_MAN.pdf
1helpful
1answer

I am trying to connect my ps3 via hdmi, digital cable box via fiber and my tv via hdmi. I cannot get the picture to display on the tv. Any suggestions?

I connected a fiber optic cable from the cable box to the receiver and connected an hdmi cable from the cable box to the tv.
1helpful
1answer

Uplinking Using Gig Copper

hello, use the plugin modules for the rj 45 connection port to uplink it.
0helpful
1answer

Fiber trunk port looses connectivity, fiber test ok

switch the fibre rx and tx around on one side of the link
0helpful
1answer

6H258-17

Zoul,

GE-1000SX stands for Gigabit short haul Multi-Mode fiber That's the SX part. This is a full duplex MMF (multi-Mode Fiber) short haul (SX) connection. It can only connect to another MMF SX enabled device. This is generally used as an uplink between switches or for a high speed connection to a server.

In short if the GE-1000SX duplex pair isn't attached to a similar interface at the other end there will be no connectivity. If you're trying to connect 100FX (100 Mb Fiber) it won't work.

Hope this helps.
0helpful
1answer

Adding a PC to the network

Make sure your network card on the computer is enabled and properly installed. Also try replacing the cable with one that is known to be good. I hope this helps. Good luck.
Not finding what you are looking for?
SMC TigerSwitch SMC8612T Logo

164 views

Ask a Question

Usually answered in minutes!

Top SMC Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2278 Answers

Joseph Hoffmann

Level 3 Expert

1756 Answers

Resolution IT Dubai
Resolution IT Dubai

Level 3 Expert

541 Answers

Are you a SMC Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...