Question about Omega Paslode 901000 Impulse Cordless Finish Nailer

1 Answer

Paslode impulse finishing gun wont fire. battery fully charged and gas is full.

Posted by bigalx on


1 Answer

D. Floyd Kolb

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 43,501 Answers


Here is a tip that I wrote about the Paslode nailers and the problems that can come up with them.

I also have a link to the Paslode manuals which contain Paslode cleaning and troubleshooting guides.

If you need parts for your Paslode, there also is a link for a site that sells the Paslode nailer parts.

Paslode Cordless Nailer Problems



Posted on Mar 06, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a cordless paslode impulse finish nailer is missfiring. the battery is fully charged, the gas chamber is full.

Hi there,

Has the tool been striped down and cleaned lately? And are you using genuine paslode gas? If not, do these two fixes first and try again.

Sep 19, 2014 | Omega Paslode 901000 Impulse Cordless...

1 Answer

Looking for the nearest repair shop for paslode nail gun in Northren Va

Have all the nails been cleared out of the tool where they were jammed? If not take the fuel cell out of the tool, and remove the battery before working on it. If still persists come back to this website for further help.

Sep 19, 2014 | Omega Paslode 901000 Impulse Cordless...

1 Answer

Paslode impulse framing nailer , iv cleaned gun and oiled , the fan works etc . seems to only fire if i have fully charged battery ,once used for about five minutes it stops firing . only way to get it...

When it stops firing is the little light on the side of the handle green or red? If it is red then the battery is draining down too quickly. Either the fan switch has malfunctioned causing the fan to run all the time (I have seen this before) or you got either a faulty battery or charger.

Mar 05, 2012 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Impulse gun wont fire and fan doesnt run

could be a bent probe not allowing full travel of the safety , fan motor, loose wire, or circuit assembly. If you are handy with tools, remove the battery and fuel cell. remove the 4 screws holding the cover on top of the cylinder assembly and down where the saety is remove the 2 screws there also. gently pull the cylinder off the tool. when you have apart check toe condition of the Oring on the top plate where the fan motor is. Now reinsert the battery and you will see a rocker switch towards the top, depress it and the fan motor should come on. if not try and depress the trigger switch and again the fan motor should come on. If neither start looking for loose or broken wires, if you find none then I would guess the terminal board would be bad. you can also remove the handle halves and look for a loose connection at the board itself, they sometimes wiggled loose where it plugs in. Good luck and let me know.

Apr 24, 2010 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Nail gun wont fire nails

you need to give more info mate , it the battery charged , is there gas in it how old ,is it filthy inside etc etc

Mar 01, 2010 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Gun will not fire, battery is charged & good ??? model #IM25011 part # 900400 Bob

problem solved - battery charger indicated that battery was charged with green light on, took battery ouit & placed it back in charger & red light came on after doing this three times the battery was fully charged and the gun worked fine.

Jan 29, 2010 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Paslode nail gun 325 black not firing

Any time these guns become intermittent or stop firing but the fan still runs, the first the to check is the expiration date on the gas cartridges. The do expire and this will make the gun work inconsistently or not at all.

Dec 08, 2009 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Shoot no shoot

make sure that the filter in the back is clean you can pop the back cover off and clean it with water if it is dirty then the excess co2 gas that the gun gives off will not be able to excape the chamber and sensors inside the gun will not let if fire. This should work for you

Sep 01, 2009 | RTO PasLode 900420 Impulse Framing Nailer

4 Answers

Paslode 350 wont fire

Probably needs cleaning. You`ll need two new o`rings.

Aug 19, 2009 | RTO PasLode 900420 Impulse Framing Nailer

Not finding what you are looking for?
Omega Paslode 901000 Impulse Cordless Finish Nailer Logo

1,872 people viewed this question

Ask a Question

Usually answered in minutes!

Top Omega Tools & Hardware - Others Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2020 Answers


Level 3 Expert

85239 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Are you an Omega Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides