Pool & Spa Logo

Related Topics:

Posted on Dec 30, 2010
Answered

My pool repair guy says I need a new circuit board for my Goldline control panel. It keeps tripping the salt cell "off". Then shows an error message "Check cell, No cell power" Where can I buy a new circuit board, 066008G-1?

Answer This Question
  • Anonymous Sep 25, 2012

    I am basically getting the same message, "Check cell, No Cell Power". I have read on youtube about soldering the K1 or replacing transister. My local pool company said its the relay. Should i trust pool guy, or attemp to pull out board and see if back of board is burnt, so i can solder and fix my self

  • Horace Sarkar
    Horace Sarkar Jun 26, 2018

    I solder board and was good for 5 yrs.

×

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 10 Answers
  • Posted on Jan 01, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.
Problem Solver:

An expert who has answered 5 questions.

Joined: Sep 03, 2010
Answers
10
Questions
0
Helped
7951
Points
17

BE CAREFUL! MANY ON LINE DEALERS CAN SEND DEFECTIVE OR REBUILT BOARDS OUT TO CONSUMERS. ONCE YOU PAY THEM ITS TOO LATE,
ANYTHING ELECTRONIC, YOU SHOULD ALWAYS BUY FROM A LOCAL POOL GUY YOU CAN TRUST.

  • fhazelton Jul 17, 2011

    Where can I buy a new circuit board

×

Horace Sarkar

Horace Sarkar

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jun 26, 2018
Horace Sarkar
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.

Joined: Jun 26, 2018
Answers
1
Questions
0
Helped
1158
Points
3

066008G Goldling PWB No Display!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0answers

Have replaced T-15 cell and calibrated yet reading went down to 800 PPM and check salt and inspect cell LCD are on. Salt level is good. What could be wrong?
Read full answer
Be the first to answer Apr 27, 2016 • Hayward-Goldline Aqua-Rite Electronic...
0answers

I need to have a web address to locate a troubleshooting guide to this salt in ground pool system
Read full answer
Be the first to answer Jan 27, 2016 • Hayward-Goldline Aqua-Rite Electronic...
0answers

Control panel shows flow ok then power light comes on for about 10 second thens gose out still read salt, temp.voltage and ect. this is a Aqua Rite generator also check input voltage and 20 amp fuse
Read full answer
Be the first to answer Sep 13, 2015 • Hayward-Goldline Aqua-Rite Electronic...
0helpful
2answers

The waterfall is not working. How can I fix it?
To give you some advice about how to fix your waterfall probably you should specify your equipmente.
Now, without knowing a word about your system I guess the problme is the motor of your pump. If you have no experience repainng the electric board of a pump you should call an authorized repairmen
Read full answer
Jul 08, 2015 • Pool & Spa
0helpful
2answers

How do I find a part number in 066012c-1 board?
replace whole board unless you have a schematic
Read full answer
Jul 27, 2014 • Goldline Swimming Pool & Spa Chlorine...
0helpful
3answers

My goldline cell reads check cell, what does that mean?
It means you need to clean/replace your salt cell. You can go to your local pool store to get a cell cleaner. Clean the cell, then let the system adjust overnight, and check the controller again in 24 hours. If it still says check cell, it should be replaced.
Read full answer
Jul 26, 2014 • Goldline Swimming Pool & Spa Chlorine...
0helpful
1answer

Low voltage
disconnect salt cell check voltage at plug if not correct bad board if ok when disconnected bad cell or plug
Read full answer
Jul 25, 2014 • Hayward Pool Products Goldline Automatic...
0answers

Haywardnet com
Read full answer
Be the first to answer Jun 01, 2013 • Goldline Salt System Transformer -...
0helpful
1answer

I have a goldline prologic control board (also operates salt/chlorine generator) and lately it is behaving wierd. Main circuit breakers that is providing the power to the control board is tripping when I...
I would try a different breaker.
Read full answer
Aug 17, 2011 • Pool & Spa
0helpful
1answer

Goldline controls 066008g-1
control board or power supply
Read full answer
Mar 06, 2010 • Aqua Pool & Spa
Not finding what you are looking for?

View Most Popular

Pool & Spa

Related Question

Have replaced T-15 cell and calibrated yet reading went down to 800 PPM and check salt and inspect cell LCD are on. Salt level is good. What could be wrong?

  • Hayward-Goldline Aqua-Rite Electronic Salt/Chlorine Generator Control Box

1,168 views

Ask a Question

Usually answered in minutes!

Popular Questions

The lever on my multiport valve is stuck, it is on

Aqua Pool & Spa

Clorinator off no cell power.

Aqua Hayward Logic PS-16 Pool & Spa...

Goldline controls 066008g-1

Aqua Pool & Spa

Plugged in and turned on but doesn't move

Aqua Vac Tiger Shark

My Aqua logic chlorine generator reads

Aqua Hayward Logic PS-16 Pool & Spa...

Top Aqua Pool & Spa Experts

john h

Level 3 Expert

29494 Answers

Kardoc

Level 3 Expert

7503 Answers

David Spradling
David Spradling

Level 3 Expert

13524 Answers

Are you an Aqua Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...