Question about RC Apache Helicopter 4 Channel Remote Control Ready To Fly

1 Answer

Why aren't my bottom rotor blades moving? - RC Apache Helicopter 4 Channel Remote Control Ready To Fly

Posted by rgiancarli on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

Gear for prop may have come loose. check under shell

Posted on Dec 26, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my kubota lawn mower die when i mow in reverse even when i push the button?


Check the blade housing and any build up of waste which can cause too much tension on the blades when they are operating as the unit moves in reverse. The rotor head could could be jamming. With the unit turned OFF try to move the blades clockwise and counter clockwise. There should be equal force required to move the blades in either direction. If not then clear and clean all the area and especially where the spindle comes through the body from the engine. Oil and regrease all required points.

Jul 22, 2014 | Kubota Garden

3 Answers

My silver bullet helicopter wont take off, the top blade is spinning but the bottom one isnt


Kindly check the rotor carefuly.. there is one white/black color rotor fixed on the bar of Motor rotates whith motor and there is anoter rotator which attached parally with its i.e once motor rotator moves the another ones also moves (which connected with the rod of Blades) some times these rotators gets loose by time and makes the rotation of Blades weak. kindly connect the same tightly and check....

Jan 01, 2014 | Shuttle 9094 Emax Remote Control...

1 Answer

Badger insinkerator, 1/3 HP does not start. Please help...i try the red button and didn't work...the blades aren't rotating....


Use wood broomstick handle down into disposal.
Wedge broomstick against side of sink opening and rotate blades free.
Or use allen wrench on bottom of disposal to free cutter blade.

If blades rotate freely and disposal has power, and reset is not tripped or will not reset, then disposal is bad.
I wrote ez disposal replacement steps:
http://www.fixya.com/support/r7929008-replace_garbage_disposal

Sep 11, 2011 | Ace Hardware InSinkErator Badger 5, 1/2 HP...

2 Answers

I recently got a DH-1 AeroQuest Mini Helicopter. It was working fine until I crashed it against the wall. So now the top Propeller spins but the bottom propeller does not and the helicopter just spins...


I had the same problem. Bottom blade would not spin. There are 2 shafts that spin 2 gears. The outer shaft that spins the bottom blade has 2 set screws and my set screws got sheered off. I replaced both set screws and everything works now....

Sep 04, 2011 | Toys

1 Answer

My electric hedge trimmer blades do not move when it is turned on. Suggestions? hs2400 date code 20021249


Check that the bolts or screws holding the two blades together aren't too tight preventing the blades sliding. Lubricate the blades also with WD40.

Jul 14, 2011 | Black & Decker Hedge Hog 24-Inch 3.0-AMP...

1 Answer

My electric hedgetrimmers blade moves,but wont cut.


Check the screws or bolts holding the blades together are tight but not so tight that the blades aren't allowed to move relative to each other.
You may need to sharpen the blades. This can be done with a small flat file but is a tedious process and will take about an hour.

Jul 12, 2011 | Garden

1 Answer

I have a Flymo Sabre cordless hedgetrimmer, which has stopped cutting anything although the blades still move. What can I do to fix it?


If there are screws or bolts holding the blades together, check these are tight, but not tight enough that the blades can't move relative to each other. If the teeth aren't sharp, you can buy a small flat file to sharpen them. This is a tedious process and both cutting edges of each tooth need to be sharpened.

May 11, 2011 | Garden

1 Answer

Exceed Rc 2.4 Ghz WarHawk 300 RTF Co-Axial Airwolf replacement of main rotor gear. Do I drop motor out of fuselage by removing bottom blades?


In order to get at the main rotor gears, you'll have to remove both sets of rotor blades and drop the chassis. After removing the battery cage you should be able to access the two main gears. You don't need to remove the motors, but if you need to access the main gear for the lower-rotor, further dis-assembly is required. I think there's a link to a dis-assembly video for the Exceed models on rcdiscuss

Sep 20, 2010 | Exceed-RC Toys

1 Answer

Rotors not turning during operation


Confusing..You say in one line Rotors not turning during operation. next line says
The top & bottom blades are able to move freely?
Il try & help anyway.1st the water level may not be high enough to load the the wash motor & spray water.2nd the dishes or cutlery may be hitting the arms.

May 30, 2010 | Zanussi 24 in. ZD686 Built-in Dishwasher

1 Answer

Blades stopped turning on Windchaser floor fan. Everything else works fine. Have had it for about 3 yrs


can you manually move the rotor on the motor? You can remove the blades and inspect the connection of the rotor to the blades and see if any foreign objects are obstructing its motion.

Aug 17, 2009 | Dryers

Not finding what you are looking for?
RC Apache Helicopter 4 Channel Remote Control Ready To Fly Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top RC Toys Experts

Tom Chichester

Level 3 Expert

61336 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Are you a RC Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...