Power was turned off to the house. When power came back the router is blinking blue lights and can't see the modem. Disconnected the computer from the wireless and plugged directly into modem and it's works fine. Did the wireless forget it's settings?

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Site reference link:
https://www.belkin.com/us/support-article?articleNum=56519

The blinking orange power light suggests that there is a problem with your modem. The modem should be plugged into the top ethernet port of your router. Try turning off your modem for 10 seconds and then turning it back on.

Flashing power light on Router is sign of hardware failure As mentioned, you have already reset the router
You can try to hard reset the router one more time
Follow this procedure
1. Press the reset button with some paper clip 2. Wait for 10 Secs 3. Turn of Power to the router (While Reset button is still pressed) 4. Wait for 10 secs 5. Power on router 6. Wait for 10 secs and then release the Reset button
While doing this make sure reset button is pressed continuously start from Step 1 - 6
Check if Power light still blinks
If No - you can setup router like before and it will work If yes - Buy a new router or get it replaced if under warranty

Turn everything off, modem, router and computer.
It shows your router is not configured properly
Turn on the modem first and wait for a solid data/connect light.

Turn on the router, give it two minutes.

Still if problem presists you need to reset the router ..

How to reset::
Push and release the “Reset” button.
The lights on the Router will momentarily flash.
The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the reset is complete

Use your computer's web-browser to connect to the web-server "inside" the router.
Check the 'WAN' settings -- they seem to be OK, since you have Internet access.
Check the 'Wireless' settings, or just rerun the Wireless Configuration Wizard, to rebuild your wireless network.

Did you contact your internet service provider?

Try restoring the Belkin back to the factory default by powering up the Belkin and pressing the RESET button on the back of the Belkin for 7 secs. Then connect a LAN cable from the computer to the Belkin, open IE browser and type the configuration IP address and configure the wireless settings ie. SSID, encryption etc. The computer wireless cards will need to be configured with the Belkin wireless settings to allow them to communicate with the Belkin.

Hi jackmyrtue,

Here's what the lights on the front indicate:


A. Wireless Security

• OFF Wireless security is off
• Solid Blue Wireless security is on

B. Wireless-Computer Status

• OFF Wireless computer is not present
• Solid Blue Wireless computer is connected to the Router
• Blinking Amber Problem with wireless computer onnecting properly to the Router

C. Wired-Computer Status

• OFF Wired computer is not present
• Solid Blue Wired computer is connected to the Router
• Blinking Amber Problem with wired computer connecting properly to the Router

D. Router/Power Status

• When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the "router" icon blinks.
• When the Router has completely booted up, the "router" icon becomes a solid light, indicating the Router is ready for use.
• OFF Router is off
• Blinking Blue Router is booting up
• Solid Blue Router is on and ready

E. Modem Status

• This icon lights in blue to indicate that your modem is connected properly to the Router.
• It turns amber when problem is detected.
• OFF Router is NOT connected to modem
• Solid Blue Router is connected to modem and functioning properly
• Blinking Amber Problem with modem

F. Internet Status
This unique icon shows you when the Router is connected to the

• Internet. When the light is off, the Router is NOT connected to the Internet.
• When the light is blinking amber, the Router is attempting to connect to the Internet.
• When the light is solid blue, the Router is connected to the Internet.

When using the "Disconnect after x minutes" feature, this icon becomes extremely useful in monitoring
the status of your Router’s connection.

• OFF Router is NOT connected to the Internet
• Blinking Amber Router is attempting to connect to the Internet
• Solid Blue Router is connected to the Internet

I hope this helps figure out your PS3 issue.

Thanks and don't forget to leave a rating.

Mark