Question about HP PSC 1315 All-In-One InkJet Printer

1 Answer

Printer will not come on when pushing the power button

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • HP Master
  • 7,733 Answers

The power module has a safety feature inside that protects the product during a power surge. If you experienced a recent power surge, the power module might need to be reset. Use the following steps to reset the power module.

  1. Unplug the power supply from the rear of the product.
  2. Unplug the power cord from the electrical outlet, power strip, or surge protector.
  3. If the product uses a power module with a detachable power cord, disconnect the cord from the power module.
  4. Wait 15 seconds.
  5. Reconnect the power cord to the power module.
  6. Plug the power cord back into the electrical outlet. Do not use a power strip or surge protector.
  7. Check to see if the power module has an LED.
    • If the power module does not have an LED, continue to the next step.
    • If the power module has an LED, check to see if the LED lights up.
      • If the LED does not light up, contact HP to replace the power module. To buy a compatible power module, right-click the following link, How to Buy HP , and then click Open in New Window .
      • If the LED lights up, continue to the next step.
Step two: Test the power on the All-in-One Follow these steps to test the power on the product.
  1. Reconnect the power supply to the rear of the product.
  2. Press and quickly release the Power button (printer will not come on when pushing the power - c01602202.gif ) to start a Power On/Off cycle. Do not hold the button down. Figure 1: Press and quickly release the Power buttonprinter will not come on when pushing the power - c01896071.gif"/uploads/images/cprinter will not come on when pushing the power - c01733891.gif alt="c01896071.gif" class="h_mi" /> c01733891.gif If you press and hold the Power button too long, the product might printer will not come on when pushing the power - c01602202.gifthen off without restarting. If this happens, press and quickly release the Power button (c01602202.gif ) again.
  • If these steps resolved the issue , there is no need to continue troubleshooting.
  • If the issue persists , see the next step.
Solution four: Test the power with a compatible power cord from a different product If you have another available power cord that is compatible with your product, use the alternate cord to repeat the steps in Solution three: Reset the power module and test the power .
  • If the product turns on with the alternate power cord, the original power cord caused the issue. Contact HP to replace the power cord. Right-click the following link, How to Buy HP , to buy a compatible power cord.
  • If the product does not turn on with the alternate power cord, continue to the next step.
Solution five: Service the HP product If you have completed all the steps listed above and are still experiencing a problem, service the product.

If you need more help come back.

Post / thumbs / testimonial are welcome!

Posted on Dec 17, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer does not print


Instructions
    • 1 Switch the Canon MX310 off using the "Power" button, then push the "Stop/Reset" button on the control panel. Hold the button down for about five seconds.
    • 2 Push the "Power" button while holding "Stop/Reset." Hold down both buttons for five seconds.
    • 3 Release "Stop/Reset" while holding down the "Power" button.
    • 4 Push "Stop/Reset" twice while continuing to hold the "Power" button. Release the "Power" button. The power light will turn green.
    • 5 Once the light is steady green, push "Stop/Reset." Wait about three seconds and push it again. Wait three more seconds and push it one final time, for a total of three times. The power light will turn orange.
    • 6 Push the "Power" button, then lift the MX310 cover open.
    • 7 Remove both ink cartridges and wait 10 seconds. Replace the cartridges and close the MX310 cover. Wait 30 seconds.
    • 8 Push the "Power" button. Wait a few seconds to allow the printer to fully power down, then switch the Canon MX310 back on using the "Power" button.

Jul 23, 2014 | Canon PIXMA MX310 All-In-One Printer

1 Answer

Error 5b00 is comming what is the solution


Solve error 5B00

Solution:

  • Press the power button to turn off the printer.
  • Hold the "Stop/Reset" button while pushing the power button.
  • Do not release the power button, release the "Stop/Reset" button and then push it twice in a row.
  • Release the buttons.
  • Wait 20 to 30 seconds until the LED shows 0.
  • Push the "Stop/Reset" button four times in a row.
  • Push the power button twice.
  • Turn off the printer by pushing the power button.
  • That's ok.
http://www.youtube.com/watch?v=RoiBaXVhS7g&feature=player_embedded

Sep 14, 2012 | Canon MP560 All-In-One InkJet Printer

2 Answers

Canon mp287 error 5B00?


hi me uttam jaiswal i have instaled MP287 inkjet but i have problem P07 get any solution

May 20, 2012 | Canon Office Equipment & Supplies

1 Answer

I have a canon pixma mp250 and error P07 flashing.Now,I refill blac and colour cartridges,and clean ink absorber,but still flashing P07.How to reset printer? Best regards, Misko


its mean absorber full..(i think)
Check this steps :
1: Unplug power and USB
2: Open door and hold power button.
3: Connect power.
4: Close door, then release power button
5: Connect USB and an press power to use.

1 Press the power button to turn off the printer.

  • 2 Hold the "Stop/Reset" button while pushing the power button. While still holding down the power button, release the "Stop/Reset" button and then push it twice in a row.
  • 3 Wait approximately 20 to 30 seconds until the LED shows 0.
  • 4 Push the "Stop/Reset" button four times in a row.
  • 5 Push the power button twice.
  • 6 Turn off the printer by pushing the power button one more time. The printer is now reset. Next comes resetting the counter on the cartridge.
  • 7 Unplug the power and the USB cables from the printer.
  • 8 Open the cartridge door and hold down the power button.
  • 9 Reconnect the power cables while still holding down the power button.
  • 10 Close the cartridge door and release the power button. The ink cartridge is now reset.



  • Aug 11, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

    1 Answer

    My cannon scanner MP240 is getting an error E5 please help to find out the solution


    Error ink cartridges are not installed properly (Error E5)
    First power off the printer. Next, while holding STOP/RESET button, power on the printer.
    While holding POWER button, release STOP/RESET button. Then push STOP/RESET button twice.
    Wait about 20-30 second until the LED shows "0?. Then push STOP/RESET button four times.
    Finally push POWER button twice. Last step is to turn off the printer by pressing the POWER button one last time.

    Jul 07, 2011 | Canon PIXMA MP240 All-In-One InkJet...

    1 Answer

    Erreur 5b00 sur canon pixma mp450


    1. Turn off the printer ( "Power" button).
    2. Open printer cover and hold the button "Resume" (red circle in the triangle) and push and hold Power button.
    3. Release button "Resume" and then push button "Resume" 2 times and release both buttons.
    4. When printer become ready on the display write "CANON Idle".
    5. Now close printer cover and push button "Resume" 4 times.
    6. Then push "Power" button 3 times to turn off printer.
    All done. The printer is ready to print.

    Dec 28, 2010 | Canon PIXMA MP450 All-In-One InkJet...

    1 Answer

    ERROR 5B00, no me deja imprimir


    1. Turn off the printer ( "Power" button).
    2. Hold the button "Resume" (red circle in the triangle) and push "Power" button.
    3. When printer become ready hold the button "Power" and release button "Resume".
    4. Push button "Resume" 2 times and then hold "Resume" and release "Power" button.
    5. When I hold button "Resume" I push and hold "Power" button and release "Resume".
    6. When I hold "Power" button, push button "Resume" 2 times and release both buttons.
    7. When printer become ready on the display write "CANON Idle".
    8. Push button "Resume" 4 times.
    9. Then push "Power" button 3 times to turn off printer.
    All done. The printer is ready to print.

    Nov 22, 2010 | Canon PIXMA MP180 All-In-One InkJet...

    1 Answer

    La stampante continua a darmi errore 5b00, ho svuotato l'inchiostro smontando tutta la stampante ma non riesco a resettarla come devo fare? grazie


    1. Turn off the printer ( "Power" button).
    2. Open printer cover and hold the button "Resume" (red circle in the triangle) and push and hold Power button.
    3. Release button "Resume" and then push button "Resume" 2 times and release both buttons.
    4. When printer become ready on the display write "CANON Idle".
    5. Now close printer cover and push button "Resume" 4 times.
    6. Then push "Power" button 3 times to turn off printer.
    All done. The printer is ready to print.

    Nov 09, 2010 | Canon Pixma MP450 All-In-One InkJet...

    1 Answer

    My printer reset button keeps flashing. i have switched it on and off and still does not work 1p3500


    Hi there

    Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset
    Ink level notification:

    1. Push “resume” for 5 seconds for canon For MPXXX you must enter to service
    Mode.
    2. Push Power switch then remove power cord.
    3. Insert plug power cord while pressing “power switch” at the same time.
    4. Push Start/reset by step 2 continue Wait display shown “0′
    5. Push + change display from “0′ to “1′
    6. Push colour button 2 times
    7. Push Power switch again, Printer will print 1 page
    8. Open cover
    9. Unplug power cord
    10. Take out ink cartridge #40 and #41
    11. Insert plug again
    12. Push power switch
    13. Open cover (scan cover)
    14. Insert ink cartridge #40 and #41 again


    Enter to service mode for canon MPXXX

    With the printer powered off but connected to a power source, press the Power
    Button while pressing and holding the Stop/ Reset button.
    When the Power is lit, press the Stop/Reset button two times while pressing and
    Holding the Power button.
    When releasing the Power button and the Stop / Reset button (regardless of
    Order), the printer will move into a service mode. (Waiting for menu selection)

    Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
    All The Best: Pineworks

    Feb 20, 2010 | Canon PIXMA iP3500 Printer

    2 Answers

    Error number 1700 canon s9000 printer


    knowing printer manufacturers I doubt they even have a sensor to detect that its full at all, they probably based on something crumby like print count. here are some instructions to reset the waste ink tank, the instructions vary so try them until one does the job :
    Waste Ink Tank Reset

    1: Power off printer
    2: Hold Resume button then press and hold POWER, the beeper will sound once.
    3: Hold POWER and release RESUME
    4: Press RESUME twice, then release all buttons
    5: When the indicator lights steady, press RESUME three or four times. The indicator should be orange.
    6: Press Power to set data



    1. Turn off printer
    2. Hold down Resume button and press Power button.
    3. Keep holding down Power button and let Resume button go.
    4. Press Resume button 2 times then let BOTH buttons go.
    5. Green lights will flash and then stop blinking.
    6. When green lights are solid, press the Resume button 4 times.
    7. Press the Power button and the printer should turn off, if not, press the Power button once more.
    8. Your printer should respond as normal.



    1. power off Printer
    2. Push and hold resume button and push power button
    3. Hold Power button and release Resume button
    4. Push Resume button twice ( 2x ), and now release resume button and power button
    5. Green light will blinking and stop.
    6. When green light on, push resume button 4 x
    7. Push Power button and printer will off, if that isn't off, push power butto again until print off position.

    Aug 20, 2008 | Office Equipment & Supplies

    Not finding what you are looking for?
    HP PSC 1315 All-In-One InkJet Printer Logo

    1,363 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Office Equipment & Supplies Experts

    Ekse

    Level 3 Expert

    13434 Answers

    Thomas F. Schneider

    Level 3 Expert

    2715 Answers

    Cindy Wells

    Level 3 Expert

    6063 Answers

    Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...