Question about Xerox Phaser 6360 Laser Printer

1 Answer

Reset xerox phaser to factory settings - Xerox Phaser 6360 Laser Printer

Posted by henry_bulloc on

Ad

1 Answer

ca555

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 57 Answers

Try performing an NVRAM reset, located in 'Troubleshooting', 'Service tools', 'NVRAM reset'. I would advise printing out a configuration page first 'Information', 'Information Pages', 'Configuration Page'.
Hope this helps.

Posted on Jan 19, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How set factory default xerox 7800


Solution : Reset the Printer to the Factory Defaults (Reset NVRAM) WARNING: Only use the tool when directed to by Xerox Service. All user and system settings will be lost.
  1. Select [Printer] on the Touch Screen.

    7800-printer-menu-select.png


  2. Select the [Tools] tab.
  3. Select [Setup].

    6700_touch_screen_tools_setup.png
  4. Select [Service Tools].

    7800-ts-tools-setup-service-tools.png
  5. Select [Reset NVRAM]. A confirmation screen will be displayed.

    7800-ts-tools-setup-service-tools-reset-nvram.png
  6. Select [Reset NVRAM] again.

    7800-ts-tools-setup-service-tools-reset-nvram1.png
Related Knowledge Bases:

Mar 05, 2014 | Xerox Printer Division Xerox Phaser...

1 Answer

Reset fuser on Xerox phaser 7760


You don't need to reset it it. It should automatically reset with no problem you can try to clear the NVRAM . Careful because you will lose all the information you have stored in it like any IP address or specific settings. What it will do is bring the printer to"factory default settings. You can do it in "service diagnostic mode. goodluck

Feb 19, 2014 | Xerox Corporation 7760/Dn - Xerox Phaser...

1 Answer

How to reset Xerox Phaser 3100 to factory settings?


First you have to enable the admin mode:
press and release: (down arrow) * #
on SOS1 change the 8th bit to 1 (counting right to left)
ie: 00100001 to 10100001 {press OK to confirm}
Now the admin menus are enabled.
To <Erase all. Reset to default configuration>
press (and release): (down arrow) #7

Feb 19, 2013 | Xerox Phaser 3100MFP

1 Answer

Phaser 6120 stuck at Printer Starting screen


what problem were you having that you chose to "reset" the printer ?

Tallon41

Sep 12, 2012 | Xerox Phaser 6120/YN Laser Printer

1 Answer

Reset to factory settings xerox phaser 3250


Reset to factory settings xerox phaser 3250 - Fixya

www.fixya.com/.../t12176778-reset_factory_settings_xerox_phaser_325...
Mar 26, 2012 - A hardware module is used to reset Xerox Phaser 3100 which work as permanent solution. After that you can refill unlimited number of times without ...

Mar 26, 2012 | Xerox Office Equipment & Supplies

1 Answer

Set factory default


Go to the menu, look in setting and scroll through until you see factory default setting. The functionality you're looking for should be in this area.

May 02, 2010 | Xerox Phaser 6200N Laser Printer

1 Answer

How do I reset a Xerox Phaser 4500 Centreware password to factory default.. or what is the factory default password? I have on which has been changed and nobody seems to know the PW anylonger


this should restore it to default.


By default there is no username or password required to access CentreWare Internet Services. If a username and password have been configured for CentreWare Internet Services and you do not remember the username and / or password, reset the printer to factory defaults (NVRAM reset).
To reset the NVRAM, go to the front panel's Main Menu:
  1. Select Troubleshooting, then press the OK button.
  2. Select Service Tools, then press the OK button.
  3. Select Reset NVRAM, press the OK button.
  4. Select Reset NVRAM and Reset Printer NOW, then press the OK button to reset all the settings to their factory default values.


Mar 03, 2010 | Xerox Phaser 4500 Printer

1 Answer

Phaser 7700 prints slow


You have to clear the memory.. once you clear out the memory then it will work properly again. What this does it loads up the factory settings.

1. From the Main Menu, highlight Support and press OK.
2. Highlight Service Tools Menu and press OK.
3. Reset NVRAM is displayed, press OK.
4. Highlight Reset NVRAM and Reset Printer NOW and press OK to reset all
the settings to default.

Sep 28, 2009 | Xerox Phaser 7750DN Laser Printer

2 Answers

Need solutons for xerox phaser 3100 after refill message toner empty. how to reset and usr this cartridge


need solutons for xerox phaser 3100 after refill message toner empty. how to reset and usr this cartridge

Aug 08, 2009 | Xerox Phaser 3100MFP/S Laser Printer

1 Answer

Password Problem Phaser 6120


Unfortunetly, you will have to reset the printer. Using the control panel go to the default setting and scroll to reset to factory settings. Then select yes and that should take care of it. If not, then in the rear of the printer under the cover, upper left side you will find the memory button battery. Remove the battery, unplug the unit, and turn it on for about a minute. Turn it off and put it back together and you should be ok. Good luck.

Feb 19, 2009 | Xerox Phaser 6120/YN Laser Printer

Not finding what you are looking for?
Xerox Phaser  6360 Laser Printer Logo

2,795 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

docukaaf

Level 1 Expert

38 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...