I took off the top to clean my husbands blades & screen and the inside poped off and I can't get it back on. Please advise.

The fan blade touching the interior back cover????

May be the fan motor shaft is too long or may be he did not push the fan blade well inside into shaft so it is to much out. Thus touching the wall cover plate..????

You connect the blades together with the plastic part the correct way through the top of the small moving blade. The plastic part becomes a guide to keep the 2 blades running straight and true. Then engage the plastic part into the motor cam shaft and the 2 tension springs at the same time and wriggle it onto the screw hole posts and fit & tighten the screws. Lubricate and you're done.

Hello & Welcome to FixYa

Error E63 in your Electrolux Dryer indicates that the temperature inside is too hot/overheating, to start with check the vent and try to clean it. If still it's not resolved then the issue is with the thermal fuse going bad and needs to be replaced. It is mounted to the exhaust duct inside the back cover panel. Please get back to me if you have any other questions.

Kevin

It's a hack, but you can use needle nose plyers to let you pry open those razor blade heads to clean the blades inside the heads. My Arcitec shaver stopped working after being clogged, rather than pay $50 for new blades, I just opened it up, took out the blades and cleaned it with an old toothbrush and soap.

Mine does it too, I finally just tried something else when I was cleaning the blades. I took some alcohol on a qtip and with the blades out of the machine I wiped up and down the line wires that are inside that go from the top to the bottom, and also the little balls that are on the bottom of the wires that slide when you turn your unit upside down. It seems to work, I do it every time I clean the blades. scribner062

You can get the foil screen and the cutter block as a set, since it is recommended to replace them as a set, in case the blade cartridge had a damaged cutter blade that could ruin the new foil screen.

You can get them from Electric Shaver Store or look elsewhere for Braun Item#: 5774761 UPC: 4210201635000

Here's a link to them, they are temporarily out of stock, but they get them in frequently.

http://www.electricshaverstore.com/get_item_5774761.htm

Hope you find this Very Helpful and best regards!

I took my andis ceramic edge blade apart to clean. Now my clipper will no longer cut my dog's hair

Most likely cause of your trouble is dust on the small mirror inside you set. Your DLP set has 2 mirrors not including the DLP chip itself which has about 500,000 tiny mirrors. The 2 mirrors reflect the DLP chip image to the screen you view. The first is the main suspect it's about 4inches by 7inches. It's mounted on the bottom center facing backwards. This mirror faces slightly up and somtimes after time dust, smoke, dirt settles on it . The second fills the space of the entire back of the cabinet but it faces down and takes alot longer to get dirty.
The compartment is sealed but dust seems to find it's way in. If you remove the screws that secure the screen assembly from the top , sides and bottom. Make sure to have a friend available the screen assembly is delicate when it's not mounted to the cabinet. You can remove and clean the mirrors. These mirrors are glass and you can use glass cleaned. Don't use glass cleaner on the screen it's plastic. You can clean it if necessary with plastic cleaner only. Probably not needed.
Good luck.

I wouldn't recommend it. Grinder needs to be opened up from the top where the ceramic blades are and that section needs to be cleaned out. The coffee in there will compact and mold quickly. Just unscrew the top screw by the hopper. There should be a rubber circular housing you can remove. From there set the grinder setting to the coarses setting (all the way to the right, and not 1.) Look at the blades and there should be markings in red and blue, align the red with red or blue with blue until the top blade easily detaches. Clean inside the that area and **** out all the coffee. Replace top blade, set red to blue so it locks the blade in place, replace arm and hopper.

Hi, dealer cost on the screen assy. is $290 plus s&h which is probably about $45, been quite awhile since I ordered one so not sure on s&h. You may be able to seperate the 2 screens and clean it up depending on what caused the mark, be advised you clean these with warm water and a LITTLE dish detergent . NEVER use windex or any other chemical type cleaner. rub gently straight down on front screen and in a circular motion on the inside screen. Before seperating the 2 screens mark both of them with a piece of tape at the top edge so they go back together exactly as you took them apart or the image will be all blurred, hope this helps, video-tek