Bachmann Ho Scale Train Steel Ez Track R&l Turnout Bonus Set Logo

Related Topics:

Question about Bachmann Ho Scale Train Steel Ez Track R&l Turnout Bonus Set

1 Answer

New train set - train goes at speed in one direction, very slowly in the opposite direction.

Posted by carliconserv on

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

Get a meeter and check the volts on the line both ways,,,there DC volts both should read the same near as can be,,,,if volts are the same both ways on the lines,,, its the trains motor,,,,

Posted on Nov 27, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

I don't know how to turn the ho engine on

You use the train controller. Set the control to zero for off and then rotate it through the scale up to one hundred for full speed. Use the sliding direction button above the speed control to select direction of the train. As far as I know there is no on/off switch on the loco itself.
0helpful
1answer

I had the twin engine gg1 2360 repaired and the engines are running in opposite directions

it sounds like whoever did the repair reversed the pickup wires on one of the units.
0helpful
1answer

Mini phantom helicopter operating problems

Throttle slowly push on, until you fly the plane slowly so far (oneself fumble balance hovering position. But the movement wants slow, after all, the air force and reaction force have a reaction time)

Trimming is your plane total 360 degree turn the regulation has two screw rotation speed, let autobiography speed equal, also will not autobiography, how to adjust to the half empty when hovering in the opposite direction to the plane of the autobiography twist


The direction of the plane is you another joystick control and control is go around and control is to adjust the direction
Dec 07, 2012 • Toys
0helpful
1answer

New bright santas christmas express no, 187 train wont smoke

This goes back about 40 years for me. Both Lionel and TYCO had "smokers" in their train sets. My recollection was that the "special smoke oil" was a mixture of very highly refined kerosene and parafin wax. Try a hobby shop such as Hobby Town or some such.
0helpful
1answer

Lionel Train transformer goes full throttle only

Sounds like the "variable resistor" that allows for a variable speed is either defective, or has become corroded on it's switch contacts. You might get lucky with some electrical contact cleaner spray and spraying it in or around the variable speed switch. Otherwise, I'd just invest in a new transformer.
0helpful
1answer

I have a 1950's engine and transformer. I run it every year a Christmas. Last year the reverse direction switch started working intermittently. I would press it multiple times and occasionally it would...

Turn the power to the track off and then back on. The engine may stay still because the train is in neutral. Turn the power off and on once again. The engine should now go forward or reverse. Turning the powere on and off again will return the train to neutral. On and off again should make the train move in the opposite direction. If all of these steps work then the problem is in the "Direction" button of the transformer. But if the problem still persist, than the "E" unit in the engine needs to be serviced. More times than not it is the E unit. The direction button is a simple momentary off switch that has few moving parts.
0helpful
1answer

I have a quantum 600 power chair. when I move the joystick in any direction the chair goes into drive like normal but doesn't want to move and moves very slowly even after i change the speed setting.

Sounds like you need new batteries. Assuming that the chair is programmed for a faster speed and has gone faster in the past the most likely culprit is old or discharged batteries. The charger or plug may be at fault also. Also check that the charger is plugged in and the indicator lights of the charger are on.
5helpful
2answers

The Belt of my craftsman 3x21 sander slowly moves off track.

There is a leveling (screw/knob) on the side of the belt sander. Turn it up and the belt will drift in one direction. Turn it downward and the belt will drift in the opposite direction. play with this leveling screw/knob until you reach a good balance and the belt will stop drifting.
Not finding what you are looking for?

232 views

Ask a Question

Usually answered in minutes!

Top Bachmann Crafts & Hobbies Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

57229 Answers

Tom Chichester

Level 3 Expert

62329 Answers

Carolyn Rogers

Level 2 Expert

145 Answers

Are you a Bachmann Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...