My handset suddenly powered off when i using 1 minute continue. this problem is continue

It could be a short in the magnito a dirty carb prob. Or foul plug also use fresh gas to narrow the broblem. I almost forgot check the compression.

Please be bit specific about the problem

1 Handset: {MENU} i {0}{0} 2 Base unit: Press and hold {LOCATOR/ INTERCOM} until the CHARGE indicator flashes. L After the CHARGE indicator starts flashing, the rest of the procedure must be completed within 1 minute. 3 Handset: Press {OK}, then wait until the handset beeps.

When this happens, the handset is in a frozen state, and to resolve it you will need to remove the battery while the handset is on and then reinstall it after 1 minute and power up the handset. If this is a continual issue, then you may want to get another handset. If the device is under 1 year old, then it will be covered by the manufacturer's warranty, and your wireless provider can initiate the exchange.

Problem My handset displays either LOAD DELTA FILE or LOAD DEFAULT DELTA FILE. What should I do?
Solution(s) Tip 1 of 2
If the handset is not responding normally, you may need to reset your telephone system. Complete the following steps to reset the telephone system:
Step 1: Disconnect the power to the telephone base.

Step 2: Disconnect the handset battery.

Step 3: Wait a few minutes and then reconnect the power to the telephone base.

Step 4: Reconnect the handset battery

Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.

Remove all handset batteries and leave for 10 minutes.
Unplug main cradle and reconnect after 30 Seconds.
Replace all handset batteries and place handsets back on cradles.

To deregister ALL handsets:
Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

Step 4: All handsets will show NOT REGISTERED.

To register a handset (register 1 handset at a time):
Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

REPEAT THE REGISTRATION PROCEDURE FOR EACH SYSTEM HANDSET.

Make sure the handsets are not receiving interference from other appliances, cell phones, etc.

IF deregistering does not work .. you will need to reset the entire system
Step 1: Disconnect the power to the telephone base.

Step 2: Disconnect the handset battery.

Step 3: Wait a few minutes and then reconnect the power to the telephone base.

Step 4: Reconnect the handset battery

Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.
You will need to set the time and date again after resetting the entire system.

Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

Step 4: All handsets will show NOT REGISTERED.

To register a handset (register 1 handset at a time):
Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

disconnect battery for few minutes, put it back in and charge for around 15 minutes. This cleared my faulty handset which would not turn on

Tip 1 of 2 Recradle the handset for 15 seconds, then lift the handset and press PHONE. Tip 2 of 2 If the handset is not responding normally, you may need to reset your telephone system. Complete the following steps to reset the telephone system: Step 1: Disconnect the power to the telephone base. Step 2: Disconnect the handset battery. Step 3: Wait a few minutes and then reconnect the power to the telephone base. Step 4: Reconnect the handset battery Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again. If that does not work, call the manufacture at 1-800-595-9511. Or take it back to where you purchased it and have then exchange it.