Question about Schlage BE365-CAM BE365CAM505 Lifetime Polished Brass Electronic Security K

1 Answer

.how to reset code push

Posted by thecarspot on

Ad

1 Answer

Coaltowner

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

There's a video that shows you how.

Good luck!

Posted on Mar 06, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change baterry o schlage be365


To change the battery on the BE365, you need to remove the inside cover by removing the two screws (one above and one below the deadbolt knob). Be careful to tuck the wires inside the lock so that they will not be crimped when you put the cover back on.

Do you here a beep and see a flashing light? Usually if pressing the Schlage button unlocks the deadbolt, your installation was done improperly. The cam on the base plate must be vertical and the bolt must be correctly installed.

You will always be able to lock and unlock the deadbolt with the inside thumb knob.

I hope this helps.

Cindy Wells

Dec 04, 2013 | Schlage BE365-CAM BE365CAM613 Oil Rubbed...

1 Answer

How do you unlock a red blinking camelot schlage Lock?


i would remove the inside half and take the battery out or reset if there is a reset button

Jan 01, 2013 | SCHLAGE LOCK COMPANY Schlage BE365VPLY505...

1 Answer

Shlage keypad dead bolt unlocks when you press the


Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial?
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Videos for installing and programming can be found on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Scroll down and find them under the heading Electronic Security--Keypad deadbolt 365

Aug 31, 2012 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

Door will unlock without entering code


"Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial? "
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Feb 15, 2012 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

Schlage camelot key pad does not engage exterior locking knob when you press the schlage button. I have tried three different locks.


Here is a link to the installation instructions:

http://consumer.schlage.com/Project%20Documents/P515-858.pdf

It sounds like you may have the Turn Lock Feature disabled. View and scroll down in the instruction sheet to the Troubleshooting portion, where it says " Pressing (the) Schlage (button) does not rotate deadbolt" The solution is to push the PC button, then the Schlage button, then 7 to enable the turn lock feature.

Here is the contact info you need for customer service:

Schlage Lock Company
Customer Service Department
2119 E Kansas City Rd
Olathe, KS 66061
United States Customer Support
Warranty & Technical Information: 1.888.805.9837

http://consumer.schlage.com/Service-Support/Pages/ContactUs.aspx

May 02, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

I have followed the instructions on how to change my entrance code, but am not being successful. I even changed the nine volt thinking that might be the problem. It blinks red quite a bit. Do I have to...


Here is a very useful link to a video on reprogramming the BE365 lock:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Apr 26, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

Do I have to reprogram my lock after changing the battery?


Does the Schlage Keypad Lock or Keypad Deadbolt need to be reprogrammed after changing the battery? The Schlage Keypad Lock and Keypad Deadbolt does not need to be reprogrammed after replacing the battery. All settings are retained in the memory of the lock, including valid user codes and the programming code.

I'm including a link to the pdf file of the complete installation and programming instructions:

http://consumer.schlage.com/Project%20Documents/P515-859.pdf

You may also find more useful information on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx#1

Apr 05, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

I have a BE365 Lock on my door. When I go to lock the door it wants the code punched in and the knob turned. When i unlock it, it just wants the schlage button pushed and knob turned. HELP


How do I enable the alternative setting (Code Turn)? (BE365 Deadbolt only)
1.) Enter your current 6-digit programming code
2.) Push the button
3.) Press 7 on your keypad

Nov 16, 2010 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

How to change the battery on my BE365-CAM-716 Schlage Keypad Deadbolt


Problem fixed by having my wife look it up on the Schlage website. The deadbolt has a flash memory so your combinations and codes will not be lost when the batteries are changed.

Sep 21, 2008 | Schlage BE365-CAM BE365CAM613 Oil Rubbed...

Not finding what you are looking for?
Schlage BE365-CAM  BE365CAM505 Lifetime Polished Brass Electronic Security K Logo

1,250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schlage Locks & Locksmithing Experts

JOHN LAPIER

Level 3 Expert

2601 Answers

Mike

Level 3 Expert

4369 Answers

Cindy Wells

Level 3 Expert

6182 Answers

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...