Replace control panel - Frigidaire PLES389D Electric Kitchen Range

To replace the spring on your Whirlpool washer SM8525492-B, you may need to remove the upper control panel. Here are some steps you can follow to do this:
1. Unplug the washer from the electrical outlet to ensure your safety.
2. Remove the end caps on each side of the control panel. These end caps are located at the top of the washer and can be removed by pulling them off.
3. Once the end caps are removed, use a screwdriver to remove the screws that hold the control panel in place. There should be two screws, one on each side of the control panel.
4. Once the screws are removed, slide the control panel forward to release it from the clips that hold it in place.
5. Tilt the control panel back and rest it against the wall. Be careful not to damage any of the wires or connections that are attached to the control panel.
6. You should now have access to the springs on the washer. Replace the spring as necessary, and then reattach the control panel by reversing the steps above.

If you are still having trouble removing the control panel, it may be helpful to consult the washer's manual or contact a professional for assistance.

Help in this link

https://www.google.com/search?q=2009+Hyundai+Accent.+remove+the+control+panel+to+replace+the+blower+motor+control+panel

..

Many ovens built by GE display error codes on the display when problems are detected. The F7 error code indicates that there is a problem with the buttons of the control panel. The code comes on when two or more buttons are stuck at the same time. The oven cannot operate when this condition exists. The oven is repaired by replacing the control panel with a functioning one.
Follow the steps
1. Unplug the oven power cord from the electrical outlet.
2. Open the oven door fully. 3. Unscrew and remove the two or three screws from the inside of the oven that hold down the control panel.
4. Pull the control panel toward the front of the oven. Lift the panel up to disconnect it from the oven.
5. Rotate the control panel sideways to get easy access to the data cable.
6. Remove the screws that hold the data-cable connector. Disconnect the data cable. Set the old control panel aside.
7. Plug the data cable into the new control panel. Replace the screws that hold the cable connector into the control panel.
8. Position the control panel in its correct position on top of the GE oven. Replace the screws on the bottom of the control panel from the inside of the oven.
thank you

If you need to replace the control panel altogether, there are a few things you should know beforehand. Before you purchase a new panel, make sure it's compatible with your existing spa control pack. There is often a part number on the existing top side panel when you pull it out of the housing. A sticker is typically on the side indicating a part number from the manufacturer. Otherwise, get the number for your spa control pack and call the manufacturer to find out which top side panel will work for you.

Replacing a topside control panel is a fairly simple process. First, turn off the power to the unit. Remove the spa access panel and take the cover off of the control box and unplug the wire that goes form the topside panel to the circuit board. Gently remove the topside control panel. Remove the plastic from the self-stick backing of the topside controller. Place the topside controller in the place of the previous one. Plug in the topside wire to the circuit board and power back up the spa to test the function of the new unit.

Even if you do replace the panel you still need to get rid of the cockroaches because it will keep on happening. Since the panel may be hard to find I see no other alternative then to replace it with what they suggest. I see no other option except for getting rid of your washing machine and buying a new one, so for the $60 they want to fix it seems well worth it.

Good luck,

Marty

follow this steps and fix it. God bless you

Touchpad and Control Panel

If the buttons don't work on the control panel the entire touchpad and control panel assembly may need to be replaced. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced.

Touchpad

If the buttons don't work on the control panel, the dishwasher touchpad might be at fault. Generally speaking, if the dishwasher display is working and some of the buttons respond correctly but some don't, the problem is with the touchpad.

Main Control Board

The dishwasher has a main control board which regulates nearly every function in the dishwasher. If the control panel buttons don't work, and other causes have been ruled out, the main control board might need to be replaced.

Call GE - 866-622-6184
There is a campaign to replace that part as they are defective.
They will send you the part for free, but charge you $200 to install it. The install is not too hard. Make sure you power off the oven when you do it. Instructions are included.

Hello

Unplug the microwave from the wall outlet prior to disassembling.


Open the microwave door. Remove the screws securing the grill above the door opening to the microwave. Remove the grill.


Remove the screw located at the top of the control panel, which is now visible with the grill removed.


Lift the control panel up to release the tabs securing it in place. Move it away from the microwave.


Look at the rear of the control panel to any disconnected wires that may have caused the control panel to stop functioning. If wires are disconnected, reconnect them, reassemble the microwave and determine if the problem is still occurring. If the problem still occurs, replace the control panel.


Transfer the wires from the old control panel to the new control panel.


Move the panel back against the microwave's control panel housing. Slide it down to lock it into position.


Install the screw at the top of the control panel.

Replace the grill on the top of the microwave. Secure it using the screws that were removed.


Restore power to the microwave.

Yes the control panel can be replaced and so can the "plus"button. All you have to do is open it up,take out the control panel and replace the push button for the volume.It might be cheaper than installing a new control panel.
Good luck.

G.

You need to remove the top panel before you can remove and replace the control panel. Remove the screws holding the top panel to the back of the machine and slide the panel backward.

Disconnect the user interface wiring harness from the Central Control Unit (CCU). Pull the dispenser drawer out and press down the release tab at the back of the drawer to completely pull it out.

Remove the screw that was covered by the dispenser drawer in the recessed hole next to the drawer opening.

Open the door and insert a flat-bladed screwdriver into the notch at the bottom center of the control panel to release it.

Press and release the tab behind the right hand side of the control panel securing it to the cabinet.

Gently pry up and release the top of the control panel and pull it off the cabinet.

Install the new control panel in reverse of the steps above.