LG WM2501H Front Load Stacked Washer/ Dryer Logo
Posted on Nov 09, 2010
Answered

Door is closed and the light stays on. after a while non of the buttons will work any suggestions.

Answer This Question

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Dec 31, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

Joined: Dec 31, 2012
Answers
1
Questions
1
Helped
998
Points
2

I have the same problem but my interior drum light stays on whether door is open or closed; in either case the control panel becomes in-operable after about five minutes. I unplug the machine for 5 to 20 minutes then plug it back in and it is powered "on" the moment I plug it in (i don't even have to push the power button). Then the light remains on but i am able to operate the control panel so i can do a load of clothes. Then if the machine sits idle for no more than five minutes, the control panel becomes in-operable again and the interior drum light stays on.

Any one have a clue???

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why won't Chamberlain 1040-6 garage door opener open or close?
In addition to the ANT suggestion, are you able to open/close the door with the button first? And then check the 12-volt battery in the remote control.

Work-around: Modern cars have the ability to learn the motor's code. Then I use the built-in openers on my cars to open the garage door as work-around. All you have to do is initiate the learning process by pressing a button on the motor, and then keep pressing your built-in opener's button until the light becomes steady. Try to let your car stay as close to the motor as possible.

Good luck!
Read full answer
Apr 27, 2014 • liftmaster Chamberlain Garage Door Opener...
1helpful
1answer

I have a Frigidaire washer model ftf2140fs1, the door doesn't stay closed and if it's closed it's not washing but all the buttons light up but the door lock light doesn't turn on. please...
Hi from retired Englishman in SW France,

There is likely to be a problem with either the door solenoid/lock or the 'door closed' sensor requiring a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C
Read full answer
Jul 09, 2011 • Frigidaire ATF6000ES Front Load Washer
1helpful
1answer

The door will open just fine, when closeing the door (by the wall switch) it will not close unless you hold the buttom down. The sensors at the bottom of the door has a green light on one side nad the...
Your door switch is bad. You can get one at home depot, it's nothing more than a door bell button. Your lights are correct and I bet if you try to close with your remote it works. That also will verify it's a bad button.
Read full answer
Mar 01, 2011 • liftmaster Chamberlain Garage Door Opener...
0helpful
1answer

I have a liftmaster Model 1240. Door will open by remote or wall opener. The door will only close while holding wall opener button down. If i try and close via remote, light starts blinking and door...
The only thing that will cause the main light to flash 10 times and the door to reverse to the open position is a sensor problem. Make sure the light on each sensor is on and not flickering ever so slightly. Make sure they are not moving when the door starts to close. Lights on sensors should not blink. One light should stay on constantly and the other sensors light should go off when you block the sensors.
Read full answer
Jan 22, 2011 • Sears Craftsman LiftMaster Chamberlain...
1helpful
3answers

Dishwasher won't run. Normal light and cancel light flashing cont
Hi,


The door latch pulls the door tightly closed to prevent water leakage around the door. It is also designed to prevent operation while the door is open. The door latch works in concert with the door switch to ensure that the door is tightly closed and latched.The door switch is a separate part from the door latch and is found inside the cabinet. The switch is off when the door is open. Depressing the switch closes the circuit and enables dishwasher operation. Closing the door does not depress the switch all the way. Only when the door is closed and latched, does the door fully depress the switch.

If the door latch is not properly aligned it may not pull the door tightly closed and the door switch will not be fully depressed. Unless the switch is fully depressed the dishwasher will not operate. It is a simple matter to determine whether the door latch is the problem. Simply open the door, close the latch and select a cycle and depress the switch. Note that if the test is successful, with the door open, the dishwasher will operate and water may spray out. Make sure to first remove all tools from inside the dishwasher. Do not reach inside the dishwasher during the test. Now, inspect the cabinet where the door makes contact with it and locate the door switch. It may have a protruding button or spike or more likely it is a hole with a piece of metal or plastic inside it. You must fully depress that switch. If the switch is recessed, then use a non-conductive object, such as a wooden pencil, to depress the switch.

Thank you !!
Read full answer
Jun 18, 2010 • KitchenAid 24 in. KUDS01FLBL Built-in...
3helpful
1answer

Cant get back door to stay closed . The lock is stuck in locked position I think and the door is open. When I go to close it, it is'nt staying closed. Had to duck tape it to stay closed. LOL! I keep...
It sounds to me ( correct me if I'm wrong ) like the door latch on the side vertical edge of the door is in the LOCKED POSITION. In order to unlock it perform the following. First electrically with the LOCK button UNLOCK the locks. Now with one hand hold the OUTSIDE DOOR HANDLE IN THE OPEN POSITION, while at the same time FLIPPING OPEN THE LATCH. All Done . Now you can close the door. Hope this helps
Read full answer
Jun 27, 2009 • 1997 Chevrolet Lumina
5helpful
1answer

Dome light and reading lamps stay on and will not cut off.
your door close switch is non-functional. its located in the door jamb. its a black button the size of a shirt button. usually held in by one or two screws.

there is one for each door.
Read full answer
Apr 11, 2009 • 1997 Chevrolet Cavalier
0helpful
1answer

2002 lincoln ls door ajar light stays on when door is completely closed and when this problem occurs all windows do not work
door ajar switch is usually the problem switch is a little button on the door jam that opens the circuit to the light when the door closes
Read full answer
Mar 12, 2009 • 2002 Lincoln LS
0helpful
1answer

2001 Mazda Tribute, V6, 4wd..........Door ajar light on, but door
The door switch is stuck on or the wire is shorted to ground.
Read full answer
Jan 19, 2018 • 2001 Mazda Tribute
0helpful
1answer

Power side power on 2000 sienna van does not work
Sounds like the switch in the door, that tells the car the door is closed, is not working or broken. It may be inside the door or on the door frame. It looks like a button or a slide button that when the door closes, it's supposed to close on this button and shut off the interior lights and turn off the dash light. The doors probably won't lock because it thinks the door is open with the keys in the ignition. Electrical systems are never cheap to fix and they can cost a lot of time just to figure out exactly what's wrong and where. I hope this helps.
Read full answer
Feb 25, 2009 • 2004 Toyota Sienna
Not finding what you are looking for?

View Most Popular

WM2501H Front Load Stacked Washer/ Dryer

  • Washing Machines

Related Question

Why won't Chamberlain 1040-6 garage door opener open or close?

  • liftmaster Chamberlain Garage Door Opener Transmitter 300MC

Related Topics

1,008 views

Ask a Question

Usually answered in minutes!

Popular Questions

LG Tromm WM2277HW will not spin both directions, LE error.

LG WM-2277HW Front Load Washer

Ue error code on the display

LG WM1814CW Front Load Washer

LG Tromm Washer

LG WM2688HWM TROMM SteamWasher

LG TROMM CLOTHES WASHER - "LE" ERROR CODE

LG WM-2277HW Front Load Washer

My LG washer wont turn on, if I unplug it from the wall and plug it back in, it will work for one cycle, but then the next time I go to use it, I have to unplug it again to get it to work.

LG WM2455 Front Load Washer

Top LG Washing Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...