Question about DISH Network IR Remote Control

1 Answer

Can not change channel with my new remote on my bell receiver

Posted by vfc112670 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 24 Answers

There could be a few different things causing the problem, but beginning troubleshooting would consist of the basic questions such as, are there fresh batteries in the remote and is the remote in the correct "Mode?" In order to change the satellite channels- remote needs to be in "SAT," mode, you can verify what mode the remote is in by attempting to change channels, or by simply pressing any button on the remote such as channel up or down - if the remote is in fact in sat mode the "SAT" button in the upper left hand corner of the remote will light up- this will allow you to confirm the remote is in the correct mode to allow you to successfully change channels. Also another potential issue is when you started experiencing these remote problems- has anything changed? Did you perhaps move the receiver to a different/new location? The sensor on the top of the remote and the front panel of the receiver need to have a clear path of signal in order to work, sometimes (usually rare) if the receiver is enclosed within a cabinet with glass doors this can cause an issue as well. Hope one of these tips helps; feel free to contact me directly if you need any further assistance.
-Kirstie DISH Network

Posted on Jan 27, 2011

Ad

3 Related Answers

VOTIT

LORETO LACARON

  • 2071 Answers

SOURCE: need remote code for programming a bell expressvu receiver

Here for the Jensen remote just click below;

Here is link to the manual:

http://www.remotecodelist.com/remotes/jensen/JR300C.pdf


Here is some helpful information I found:
Without the code on JER-323:
1.Manually turn on the component you want the remote to control.
2. Press the device button, example:( TV) and the (power button) for 3 seconds until the (on/off button stays lit).
3. Once the (on/off) button is lit, press the (on/off) button until the unit (the TV or unit you are trying to control.) turns off.
4. When the code is located, press the (stop) button at the bottom to save the code.
Here are some codes I found for the Jensen 323:
GE VCR: 2000, 2013, 2021, 2022, 2053, 2087, 2089, 2091, 2115, 2120
Motorola Cable Box: 5000, 5003, 5046, 5047, 5052
Mitsubishi TV 0093, 0150, 0178, 0019
JVC VCR 0067, 0041, 0008
JVC DVD 0558, 0623

Hope it may help you;

Regards,
VOTIT

Posted on Jan 28, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: 3.1 IR 128053 bell remote won't change tv channels

I believe you hold the top left button until it flashes, then enter the receiver id '00' in this case and press it again.

hope this helps!

OverstockDistributing.com

Posted on Mar 14, 2010

Anonymous

  • 1 Answer

SOURCE: Hi, I have a Philips SRP4004 universal remote and

I have the same problem and sadly no solution

Posted on Dec 06, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a Philips SRP4004/27 universal remote and the problem is: on my satellite receiver (a Bell ExpressVu), every time I press ONCE the up or down button to change the channels, the receiver goes a...


I am having the same problem. Are you kidding me that no solution has been offered??? Nice company policy to support their stuff. My rec. don't buy their products. What a bunch of ****.

May 27, 2011 | Philips SRP4004 Remote Control

1 Answer

We have purchased a portable flat screen t.v. from WalMart and would like to know which company it would be compatable with for the remote as we are wanting to program 1 remote to work on the t..v, and the...


To brad6134,
We have a bell receiver and recently changed to the HD and got a new receiver and new changer. You didn't say if you have a Bell dish. We have and when went to HD , we now only have to use one changer. Before that with Bell, we needed two changers. Hope this helps.

Apr 10, 2011 | eMachines E620 COMPATIBLE LAPTOP LCD...

1 Answer

3.1 IR 128053 bell remote won't change tv channels i need to get to channel 00 what do i do?


I believe you hold the top left button until it flashes, then enter the receiver id '00' in this case and press it again.

hope this helps!

OverstockDistributing.com

Oct 17, 2009 | DISH Network IR Remote Control

1 Answer

Remote will turn on TV and Receiver, but won't show the program guide, or change channels


twicker

Your remote needs to be readdressed to the receiver if you are not able to change channels or bring up any of the receiver menus. Have you already replaced the batteries with new batteries? I have provided a link with instructions on how to readdress the remote to your receiver. Select the type receiver you have, which will open a PDF document with the instructions on how to readdress the remote to the receiver. If this doesn't resolve the issue, you may need a new remote. I hope this helps.

http://www.dishnetwork.com/SupportSection/remote-setup
Ray Calo
DISH Network

Sep 20, 2009 | DISH Network IR Remote Control

2 Answers

Bell Expressvu 2700 satellite receiver av inputs


had my 2700 reciver unpluged for awhile now can't my channels back can you give me any idea how to fix this

Jan 01, 2008 | Televison & Video

Not finding what you are looking for?
DISH Network IR Remote Control Logo

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76497 Answers

Sheldon Dedek

Level 3 Expert

912 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...