The camara will come on with fully charged batteries and u can look through the pictures. but u cannot take new photos! when i turn it to the take photo button the camara turns its self off

There are a few possible reasons why your Kodak Easyshare Z740 camera might be turning off while you are trying to take pictures:

1. The battery might be low or dead. Try replacing the battery with a fully charged one to see if this fixes the issue.
2. There might be a problem with the camera's power supply. Try cleaning the battery contacts and charging the battery to see if this fixes the issue.
3. There might be a problem with the camera's firmware. Try updating the firmware to see if this fixes the issue.
4. There might be a problem with the camera's hardware. If the camera is still under warranty, you should contact Kodak for service. If the camera is not under warranty, you may need to take it to a repair shop to have it fixed.

I hope this helps! Let me know if you have any other questions.

The Canon EOS Rebel G is an all-plastic 35mm SLR film camera there is no way this camera model can download pictures to a computer, it's a film camera. If you have miss printed the model correct the error and resubmit the question.

Reset the menus to default or factory settings.
Then test the camera again.
Make sure that the battery is fully charged or new.
You might consider to buy a new battery (Ebay is a good place) for this camera. Then test.
Problems like this can show up when the battery is weak or not fully charged.
You may try to remove the battery for 24 hours and then after try it again.

Hi there,

Make sure that your camera battery was fully charged, and the you have turn ON the camera after you connect it the the computer.

It will not automatically transfer the picture, a dialouge box will appear when the computer detects the imaging device you connect, you will then ask to pick or choose the picture you want to transfer to next destination folder. Make sure that you remember the folder you have transfer the picture, once it was transfer the photo will be automatically removed from the camera.

Let me hear from you again if you have any other more concerns.

Regards,
micro~

Here are the steps: 1. Make sure you will install a new or fully charged battery/batteries into your camera. 2. Clean the battery contacts. a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth. b. Reinstall the battery/batteries into your camera. Please make sure that you are installing a fresh/ fully charged battery c. Without the memory card, turn your camera on. 3. Please test with the a different battery If you do not have access to another battery Try these steps instead: Please take the battery out of the camera. b. Insert the charger into the unit from the main socket and turn the camera on. If the camera works you will need to replace the battery. If you camera doesn?t switch on you will need to order a No power repair or a new cable.

Here are the steps:
1. Make sure you will install a new or fully charged battery/batteries into your camera. Please use lithium batteries Ni-Mh or rechargeable Batteries (2000 M.Amp or higher).
2. Clean the battery contacts.
a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth.
b. Reinstall the battery/batteries into your camera
3. Turn on your camera without the memory card.

In order to organise your repair or Trade up please Contact KODAK:
http://www.kodak.com/eknec/PageQuerier.jhtml?pq-path=14563&pq-locale=en_US&_requestid=3490

1. Make sure you will install a new or fully charged battery/batteries into your camera. Please use lithium batteries Ni-Mh or rechargeable Batteries (2000 M.Amp or higher).
2. Clean the battery contacts.
a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth.
b. Reinstall the battery/batteries into your camera
3. Turn on your camera without the memory card.

Here are the steps:

1. Make sure you will install a new or fully charged battery/batteries into your camera.

2. Clean the battery contacts.

a. Remove the battery/batteries and the memory card from your camera, then wipe the battery contacts with a soft, clean cloth.
b. Reinstall the battery/batteries into your camera

3. Without the memory card,turn on your camera.

If issue persists, call 1.800.235.6325 for repair.

Thanks.

Neerak21

This camera is eleven years old, and is probably worn out

I have the same camera... and it was doing the same thing AFTER i changed my old batteries, because they were getting low. It was only after i put in the NEW batteries that i had this problem... I tried putting the old batteries back in and sure enough it worked again, so it probably all just depends on the brand of the battery you use.