Mounting I have a countured roof liner, therefore need a mounting console or trim ring, but cant' find one.

There is one of two way to remove them. With the roof fully open check inside the runners for mounting screws or bolts. If there are none visible it is probably mounted from inside the vehicle. If they are inside mounts you will need the glass in the closed position and with a helper it will be easier to lift out. If there is a roof liner fitted you will most likely need to remove it to gain access to the mounting bolts. Not all sunroofs can have new rails fitted so you might have to replace the whole thing.

I just Googled a picture.
There is a roof rack type trim on the roof.
Water flows downhill
3 possible sources:
- window trim
- windshield
- roof trim
I would be suspecting the roof trim. Determine how it is attached. Remove it. Clean the roof and all parts of the trim that contect the roof. Apply sealant in appropriate locations. Re- install roof trim.
Test
No leak!
Ta-Da!

I just Googled a picture.
There is a roof rack type trim on the roof.
Water flows downhill
3 possible sources:
- window trim
- windshield
- roof trim
I would be suspecting the roof trim. Determine how it is attached. Remove it. Clean the roof and all parts of the trim that contect the roof. Apply sealant in appropriate locations. Re- install roof trim.
Test
No leak!
Ta-Da!

cut the roof liner dummy

BEHIND THE INNER COVER AT THE RIGHT OF THE TRUNK.U MUST TAKE OUT THE COVER..

1 - Flap for convertible roof compartment Note
t The variable convertible roof compartment must be in the bottom position. t To remove flap for convertible roof compartment -1-, hinges -2- do not have to be removed. t Arrow points in direction of travel. q Bend flap for convertible roof compartment -1- on one side at hinge and disengage flap for convertible roof compartment -1- at hinges. q Fold down flap for convertible roof compartment -1-. q Disengage flap at hooks -4- (2x) by sliding it towards front. 2 - Hinge (2x) q Bend flap for convertible roof compartment -1- on one side at hinge and disengage flap for convertible roof compartment -1- at hinges. q Unscrew bolt -3-. q Disengage hinge -2- from body. 3 - Bolt (2x) 4 - Hook 5 - Variable convertible roof compartment

THEN REMOVE THESE..

1 - Side trim (right-side) t Removing - Take out floor covering in luggage compartment. - Remove rear cross panel trim ? Chapter. - Remove trim for handle mounting ? Chapter. - Remove flap for convertible roof compartment ? Chapter. - Remove luggage compartment light ? Chapter. - Unfasten clip -2-. - Pull off side trim (right-side) -1- in direction of arrow. t Installing Note
t Following installation, make sure seal is properly in position over trim. - Install trim in reverse order of removal. 2 - Clip

UNDER THIS TRIM U WILL FIND THE MOTOR WITH THE TANK.USE HYDRAULIC OIL THAT U PUT AT THE STEERING RESERVOIR......BEWARE THE SAE OF THE OIL!!!!!
GOOD LUCK

Start with the first, front supporting wire / rod & feed it through the lining hoops & roof mounts, then work your way back along the roof doing the same for each rod. This rods fully support the liner & do most of the work.

When all the rods are fitted, start loosening any trim where required, push the liner under & re-seat the trim. Use a blunt tool to lift the edge of any window seals & run it slowly along the seal, inserting the edge of the liner as you go

The 2001 Dodge caravan has 2 heater cores - front (the main one), and the rear. Removal of the
rear heater core is a whole different procedure than the front.

Front Heater Core - Removal and Installation

1. Before servicing the vehicle, refer to the Precautions Section.
2. Align the wheels in the straight-ahead position.
3. Disconnect the negative battery cable.
   CAUTION Before working around the steering wheel or the instrument panel all 2 minutes to pass to allow the air bag module to discharge.
   
4. Drain the cooling system into a clean container for reuse.
5. Remove the steering column, by removing or disconnect the following:
   
   Lower left side steering column cover Parking brake release cable from the parking brake lever 10 steering column cover liner-to-instrument panel bolts and the cover liner
6. Rotate the key to the LOCK position; then, rotate the steering wheel to the LOCKED position.
   
   Gear selector cable and its mounting bracket as an assembly from the upper steering column mounting bracket 2 instrument cluster trim bezel-to-instrument panel screws, retaining clips and bezel 2 steering column shroud-to-steering column screws and the shroud Steering column-to-intermediate steering shaft coupler
   
7. Loosen but do not remove the 2 lower steering column mounting bracket nuts/washers.
   
   2 upper steering column mounting bracket nuts/washers Steering column assembly from the vehicle
   
8. Remove or disconnect the following:
   
   Instrument panel-to-chassis harness interconnect and bracket Lower silencer boot, at the base of the steering shaft
   
9. Working in the engine compartment, pinch off the heater hoses.
   
   Heater core cover. Position some towels under the heater core hoses. Heater core plate and the hoses
   
10. Depress the heater core retaining clips.
11. Lift the accelerator pedal and slide the heater core past it.
12. Depress the brake pedal and remove the heater core from the heater/air conditioning housing assembly.
    
    

    Fig. View of the steering column assembly
    
    
    

    Fig. View of the interconnect and bracket
    
    
    

    Fig. View of the front heater core assembly
    

To install:

1. Depress the brake pedal and install the heater core into the heater/air conditioning housing assembly.
2. Lift the accelerator pedal and slide the heater core past it.
3. Install or connect the following:
   
   Heater hoses (using new O-rings) and the heater core plate Heater core cover Heater hoses clamps, working in the engine compartment Lower silencer boot at the base of the steering shaft Instrument panel-to-chassis harness interconnect and bracket
   
4. Install the steering column assembly by installing or connect the following:
   
   Steering column assembly, carefully into the vehicle. 2 upper and 2 lower steering column mounting bracket nuts/washers. Torque the nuts to 105 inch lbs. (12 Nm). Steering column-to-intermediate steering shaft coupler and tighten the pinch bolt to 21 ft. lbs. (28 Nm) 2 steering column shroud and the shroud-to-steering column screws Bezel, the retaining clips and the 2 instrument cluster trim bezel-to-instrument panel screws Gear selector cable and its mounting bracket as an assembly to the upper steering column mounting bracket 10 steering column cover liner and the cover liner-to-instrument panel bolts Parking brake release cable to the parking brake lever Lower left side steering column cover. Lower left side steering column cover
   
5. Refill the cooling system.
6. Connect the negative battery cable.
7. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Plenty of cars have sun roofs and roof mounted DVD players,you just need to look at where youre positioning it in relation to the interior slide sunroof trim so it isnt screwed through mounting DVD,and look at the position in relation to the passengers looking at it

remove trim at edge of liner and look above the liner ti reval a connector.

no, there should be a plastic trim. u can gently wedge off. u may need to remove part of your door rubber. easily done though.