I have a Xerox 7356 Scanner which continually says: Not Ready on the display. Any suggestions on how to troubleshoot this problem or where to go on-line to research troubleshooting?

Question edited for clarity.

Ready To Scan Your Job Message Missing on the User ...

Xerox https://www.support.xerox.com > en-us > article
Mar 16, 2020 - Power Off the Printer and Unplug the Unit From the Wall Outlet. Wait Two Minutes, Plug the Printer Back Into the Outlet and Power On.

Solved: Xerox 5735 Scan Issue - Customer Support Forum

Xerox Support Forum https://forum.support.xerox.com > td-p
Jan 2, 2019 - Solved: Hi, I am using Xerox workcenter 5735 in my office, i cant able to see scan option in my GU interface on my PC. please tell me what ...

Xerox WorkCentre 5735 - Scan To Home option not ...
5 posts
Jan 5, 2015
Enable workflow scanning - Customer Support Forum ...
7 posts
Jan 3, 2019
Scan to Email problem With WC7535 - Customer ...
5 posts
Aug 8, 2018
Scanning does not work - Customer Support Forum - Xerox
3 posts
Jan 18, 2021
More results from forum.support.xerox.com Missing: 'Ready ‎message

Xerox® Xerox WorkCentre 5735/5740/5745/5755/5765/5775

Niagara College Canada https://its.niagaracollege.ca > uploads > 2017/06
Note: If using the document glass to scan originals, the device displays a message when ready to scan side 2. Continue scanning until all sides have been ...
160 pages

Check your settings and make sure that the folder has not been moved to another location.

Verify the scanner drive sistems,motor or the scanner home sensor .

LSU stands for Laser Scanner Unit. It comes up only if you are trying to access scanner services like scanning a document, using fax or simple scanning.

If it's coming continuously you might need to check connectors within the scanner. Best way is to call a technician from Xerox or take it to their store.

As far as the scanner insert a sheet to copy and when it says NOT READY instead of rolling the paper out the way you put it in, roll it forward until it comes out the back.

An LL-22 is a HV power supply error. Most of the time when I see this the corotron wires are contaminated by developer. You need to clean it with a vacuum.

this is a problem related with CCD

Did you receive any good solutions? I have a Dead Display on a Xerox Phaser 6120. Thanks!
Rick
[email protected]

n5t

The flashing green light has the following meaning:

• Blinking green: indicates the scanner is waking up from power
saving and preparing to scan.
• Steady green: indicates the scanner is ready to scan.

How to Adjust the Power Save Settings for the DocuMate 252
1. Right-click on the One Touch icon and choose Show
Hardware from the pop-up menu.
You can also click the scanner icon at the top of the One Touch
Button Panel.
If the Hardware View of the panel is open you can also right-
click on the DM252 icon.
The Hardware Properties dialog box opens and shows
information about your Xerox DocuMate 252 scanner.
2. Click the Properties button.
Your scanner has a built-in power saving feature that is set to
power down after 15 minutes of idle time. You can change the
time before the scanner powers down, from 1 minute to a
maximum of 3 hours.
3. Click the arrows for the Lamp timeout setting and choose a
time setting.
To return the scanner to its factory settings, click Reset Device.
4. Click OK to save the changes and close the dialog box.

Let me know if this solves the problem and thank you, Binary Bob

Is the display saying NOT READY, or is it not comming on.
If the display is blank there is a known problem with those displays and Xerox will replace them free of charge.
If you have a blank display, call 1-800-835-6100.
If I am misunderstanding the issue provide more details please.