Question about Whirlpool Ultimate Care II GSW9650LW Top Load Washer

1 Answer

How much is the pump? - Whirlpool Ultimate Care II GSW9650LW Top Load Washer

Posted by delittle1001 on


1 Answer

Ron Coons

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Whirlpool Master
  • 2,651 Answers

If its the drain pump your lookin for heres the part number #3363394 .. retails for about $50, find it online for a few bucks cheaper..

Posted on Oct 09, 2010


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Do you have to drop the engine to replace oil pump in 2007 gmc yukon

You have to remove the engine front cover (over timing chain) and remove the oil pan to get the oil pump in and out. You don't have to remove the heads, however.

Removal & Installation

4.8L, 5.3L, 6.0L & 6.2L Engines

Fig. Exploded view of the oil pump mounting-4.8L, 5.3L, 6.0L and 6.2L engines

Fig. Oil pump disassembly-4.8L, 5.3L, 6.0L and 6.2L engines

  1. Remove or disconnect the following:


    Do not allow dirt or debris to enter the oil pump assembly, cap ends as necessary.


    The internal parts of the oil pump assembly are not serviced separately (excluding the spring). If the oil pump components are worn or damaged, replace the oil pump as an assembly. Do not attempt to repair the wire mesh portion of the pump and screen assembly.

    Engine front cover Oil pan Oil pump screen bolt and nuts Oil pump screen with O-ring seal. O-ring seal from the pump screen. Discard the O-ring seal. Remaining crankshaft oil deflector nuts. Crankshaft oil deflector Oil pump bolts

    Oil pump To install:


    Inspect the oil pump and engine block oil gallery passages. These surfaces must be clear and free of debris or restrictions.

    1. Align the splined surfaces of the crankshaft sprocket and the oil pump drive gear and install the oil pump. Install the oil pump onto the crankshaft sprocket until the pump housing contacts the face of the engine block.

    2. Install or connect the following:


      Lubricate a NEW oil pump screen O-ring seal with clean engine oil.


      Push the oil pump screen tube completely into the oil pump prior to tightening the bolt. Do not allow the bolt to pull the tube into the pump.

      Oil pump bolts. Tighten the oil pump bolts to 18 ft. lbs. (25 Nm). Crankshaft oil deflector

      NEW O-ring seal onto the oil pump screen

    3. Align the oil pump screen mounting brackets with the correct crankshaft bearing cap studs.

    4. Install or connect the following:

      Oil pump screen Oil pump screen bolt and the deflector nuts. Tighten the bolt to 106 inch lbs. (12 Nm) and the nuts to 18 ft. lbs. (25 Nm). Oil pan Engine front cover

Mar 06, 2015 | GMC Cars & Trucks

1 Answer

Replace water pump torrent

drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Water pump

Which engine?

  1. Drain the radiator


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.

  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    Change the water pump

    • Tools Required
    • J 43651 Water Pump Holding Tool
    • Remove the thermostat housing.
    • Remove the water pump access plate from the front cover.
    • Remove the right hand fender liner.
      1. Important: A drain plug has been provided at the bottom of the water pump assembly for additional coolant drainage from the engine block and water pump.
      Drain the coolant from the water pump using the plug at the bottom of the pump.
      1. mportant: The water pump holding tool supports the sprocket and chain during water pump service. The tool must be used or the balance shaft must be re-timed.
      Install the J 43651 into position.
      1. Tighten the bolts on the water pump holding tool into the threads on the water pump sprocket.
      2. Install the access cover bolts that were removed earlier to secure the water pump holding tool to the front cover assembly.
      3. Remove the 3 inner water pump sprocket to water pump blots.
        1. Important: Be sure to remove both water pump bolts from the front of the engine block.
        Remove the 2 water pump bolts.
        Remove the rear 2 water pump bolts.
        1. Remove the water pump.
        2. Remove and discard the water pump O-ring seal.
        Installation Procedure
        1. Important: Prior to installing the water pump, read the entire procedure. This will help avoid balance shaft chain re-timing and ensure proper sealing.
        Install a NEW water pump O-ring seal.

        1. Important: A guide pin can be created to aid in water pump alignment. Use a M 6 m x 6 mm stud. Thread the pin into the water pump sprocket.
        Using the guide pin, align the pin with the water pump holding tool.
        1. Position the water pump against the engine block and hand tighten the water pump bolts.
        2. Notice: Refer to Fastener Notice.
        Install the inner water pump sprocket bolts. After 2 are snug, remove the guide pin and install the 3rd bolt.
        Tighten the bolts to 25 Nm (18 ft. lbs.).
        1. Tighten the water pump sprocket bolts last. Tighten the bolts to 10 Nm (89 inch lbs.).
        2. Remove the J 43651.
        3. Install the water pump access plate and bolts. Tighten the bolts to 10 Nm (89 inch lbs.).
        4. Install the right hand fender liner.
        5. Install the thermostat housing.

    Aug 29, 2011 | 2006 Pontiac Solstice

    1 Answer

    Want to replace my AO Smith Mod C48K2PA105C5 pool pump with a better pump. What's a step up?

    i recommend the sta rite dura glass . it's the best pump out there! you will need to plumb it in . but it's worth it ... it's the only pump i sell .. remember to prime the pump after any pump repair + never starve the pump for water . find a used pump from your local pool pump motor repair guy and ask him how 2 take better care of your pump.. he can save you thousands of dollhair$ over the years .. jay pump guy longwood Florida

    Mar 01, 2011 | AO Smith Pool Pump Motor Hayward Swimming...

    1 Answer

    Do you give memenars about pumps .I'm a mechanical engineer ,I'm interested in working at pumps,so I'd like to take semenars about pumps.

    Well, we can have a one on one seminar by the internet.
    I've been a pumpman for 20 years. I can share with you
    my experience (household pumps, suibmersible pumps,
    turbine pumps, gear pumps, piston pumps, dewatering
    pumps, mud pumps, trash pumps, mining pumps,
    solids handling pump, etc....) Just take your pick. Just
    send in your e-mail for assistance. God bless.

    Oct 10, 2009 | Plumbing

    3 Answers

    Pump does not pump water

    Hi there. Not necessarily. Inside the pump the impellor is plastic. Sometines the fins deteriorate to the point where the pump hums but won't move water. Other times the pump hums but won't actually run. The pump is generally fixable. If you are handy you can remove the pump and take it to any pump repair shop to be reconditioned, usually for about $50-75.

    Jul 26, 2009 | Waterway 1 Hp 115 Volt 2 Speed Side...

    Not finding what you are looking for?
    Whirlpool Ultimate Care II GSW9650LW Top Load Washer Logo

    Related Topics:

    39 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Washing Machines Experts


    Level 3 Expert

    85239 Answers

    Michael Thomas
    Michael Thomas

    Level 3 Expert

    3056 Answers

    Brad Brown

    Level 3 Expert

    18563 Answers

    Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides