Access IBM screen not working

1 Turn key in electronic ignition switch control

unit to position " 1"

2 Press the system select button (S110s3)

repeatedly until the basic display (kilometer

reading display or temperature display) is

shown in the multifunction display (A1p13)

3 Briefly press trip odometer reset button (A1s3) 3

i A signal tone sounds and the voltage

times. display appears in the multifunction display

(A1p13).

4 Press lower scroll forward/back button (S110s1)

i The "Service menu" appears in the

multifunction display (A1p13).

5 Press buttons + and

-, setting of specific

functions and volume control (S111s1)

repeatedly and select "Confirmation" menu item

6 Press lower system selection button (S110s3)

i "Confirmation" appears in the multifunction

to confirm. display (A1p13) and the menu item "Complete

service" is shown against a sight bar in the

background

7 Press lower system selection button (S110s3)

i "Service confirmed" appears in the

to confirm. multifunction display (A1p13).

8 Press the upper system selection button

(S110s3) repeatedly until the "Service menu" is

shown in the multifunction display (A1p13)

9 Using the + and

-buttons, setting of specific

functions and volume control (S111s1) select

the menu item "Special work"

10 Press lower system selection button (S110s3)

to confirm.

11 Using the + and

-buttons, setting of specific

functions and volume control (S111s1), select

menu item "Service 3"

12 Press lower system selection button (S110s3)

to confirm.

13 Select the button + and

-, setting of specific i "Standard oil" or "Oil quality 229.5".

functions and volume control (S111s1) select

the specification of the engine oil used

i

If only one oil quality is approved for the

engine, no oil selection is possible.

14 Press lower system selection button (S110s3)

i The message "Item confirmed" appears in

to confirm. the multifunction display (A1p13).

Copyright DaimlerChrysler AG 10/10/06 G/09/06. This WIS printout will not be recorded by the update service. Page 1

15 Press the upper system selection button

(S110s3) repeatedly until the basic display

(kilometer reading display or temperature

display) is shown in the multifunction display

(A1p13)

16 Turn key in electronic ignition switch control

unit to position " 0"
Copyright

Try hard reset, Please unplug the tv cables and power cables for 30 min and redo the cable and check its working ....




Good luck...

Check Ceiling feature.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
? ON-SCREEN MENU
? "Power off?" message
? "No signal" message
? "Please wait...."
? P-Timer counter
Set a red frame pointer to item and press SELECT button.
Press POINT DOWN button to move a red-frame pointer to item
that you want to set and then press SELECT button. Se ting
dialog box appears.

Hi, During the boot at the THINKPAD SCREEN press the Thinkvantage key ( Blue button ) it will launch rescue and recovery and allow you to reboot factory. This only works if you did not corrupted/deleted the rescue and recovery hidden partition on the HDD. Otherwise you will need the rescue and recovery CD to proceed. IBM/Lenovo support should be able to provide you the CD. thanks and have a nice day J-

If you just want to disable the wireless lan, you can go to the control panel, network connections, and right-click on the wireless connection icon. Click on "Disable". Re-enable it by going to the same place and click on "Enable".
In order for the "Access IBM" button to work you have to have the software installed. You can tell if it's installed by looking on the start menu under programs

1. ENTERING TO SERVICE MODE
MUTE
S
(Service mode display)
3) While pressing the MUTE button,
press MENU button on TV set.
2) Press MUTE button
again to keep pressing.
1) Press MUTE button twice
on Remote Control.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
Adjustment mode
Press
Press
Service mode
Item
S Data
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
Screen adjustment mode ON/OFF: TV (ANT)/VIDEO button (on TV)
Selection of the adjustment items : Channel s/t (on TV or Remote)
Change of the data value : Volume s/t (on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : RECALL+Channel button on TV (s)
Initialization of the self diagnostic data: RECALL+Channel button on TV (t)
“RCUT” selection : 1 button
“GCUT” selection : 2 button
“BCUT” selection : 3 button
“SCNT” selection : 4 button
“SCOL” selection : 5 button
“TNTC” selection : 6 button
Convergence adj : 7 button
Self diagnostic display : 9 button

on some models the menu button is on the front disguised as the volume up/down or channel up/down buttons. you have to push both up/down buttons on either one of these to bring up the menu.

Click to "Access IBM" button , Thinkpad Configration window or webpage, Thinkpad Configuration program will appear.
GoTo : Thinkpad Config->Display->On Screen Display

You can see there or it may there on some other option, on this configuration program. It may help you.

Cheers - Parveen

Sounds like you may not be selecting the right menu buttom. The soft keys are right below the screen. these three buttons function change depending on which screen you are viewing. I have copied the instructions from the manual below. You must select phonebook to view the phone book using the round button. You must select volume to change the volume with the round button.


The Standby Screen
When the phone is in standby, the handset display shows the following items:
Handset
Ringer off icon (when the ringer is off)/ day of the week and time / battery iconHandset ID and BannerNumber of new Caller ID calls received (If there are no new Caller ID messages, the Handset ID appears here.) SUN 12:00A Handset #1 New CID: 5REDIALMENU
Using the Four-way Function Key
Your handset has a four-way function key that allows you to move the cursor (or highlighted area) on the display and access the most commonly used features at the touch of a button. By moving this key to the left, you open the Phonebook. Move the key to the right to access Caller ID information. To use this four-way key, place your thumb over the key on the station and move to the four positions to get the feel of how it moves and operates.
Using the Handset Menu
To open the menu, press the MENU soft key. Highlight the option you want by pressing the four-way function key. This will move the cursor; the option currently highlighted appears in reversed out text. Select the highlighted option by pressing the OK soft key. To exit the menu and return to standby, press [].
If you do not press a key within 30 seconds, the phone will time out and exit the menu. When setting Date and Time, the time-out period is extended to two minutes.
Note: For GLOBAL SETUP and DEREGISTRATION menu options, make sure the line is not in use and the handsets are within range of the base. 123abcdefView the phonebook Four-way Function KeyUpView the Caller IDDown123abcdefView •