We have a model F-18 sn 9901807 but no manual to know how many minutes it takes per load & wether it recycles rinse water for the nextwash etc.Can you help?

On average, washing machines use 19 gallons of water per load, and the average household runs between 5 and 6 loads per week. Based on those figures, most washers use up to 5,605 gallons of water annually.
Front-load washers use an average of 12.5 gallons of water per load, while top-load washers average 19.6 gallons per load. Older top-load models manufactured decades ago use 40 or more gallons of water per load.

Possibly reading the meter incorrectly...

ck here...
https://plumbingsniper.com/how-to-read-a-water-meter/

My 1.5" water line to fill my pool puts out 12 gallons a minute
it would take 45 minutes running full out to put out 530 gallons.

Best to you.

The voltmeter test provides general indicator of battery condition. Check the voltage of the battery to verify that it is in a 100 per cent fully charged condition. If the open circuit or disconnected voltage reading is below 12.6 V, charge the battery and then recheck the voltage after the battery has set for one to two hours. If the voltage reading is 12.8 V or above, perform the load test described below.



The load test measures battery performance under full current load and is the best indicator of battery condition. Load testing a battery tat is not FULLY CHARGED i.e. at 12.8 VDC can permanently damage it. Fully charge it first and then let it stand for at least an hour before the load test is done. You also need a load tester AND you should know how to perform a load test. Often the best way to load test a battery will be to take it to a battery shop and have it done there.



VOLTAGE and STATE OF CHARGE FOR AGM BATTERIES IS:

12.8 VDC is 100 per cent

12.6 VDC is 75 per cent

12.3 VDC is 50 per cent

12.0 VDC is 25 per cent

11.8 VDC is 0 per cent



COLD CRANKING AMPERAGE (CCA) for a DYNA battery is 270

Battery Charging Rates/Times (Approximate)



FOR A 19 AMP HOUR DYNA AGM BATTERY



BATTERY STATE OF CHARGE is 12.8 VDC is 100 per cent Charge; Rate of Charge is N/A



BATTERY STATE OF CHARGE is 12.6 VDC is 75 per cent Charge; Rate of Charge at 3 AMP is 1.75 hours at 6 AMP is 50 minutes at 10 AMP is 30 minutes at 20 AMP is 15 minutes



BATTERY STATE OF CHARGE is 12.3 VDC is 50 per cent Charge; Rate of Charge at 3 AMP is 3.5 hours at 6 AMP is 1.75 hours at 10 AMP is 1 hour at 20 AMP is 30 minutes



BATTERY STATE OF CHARGE is 12.0 VDC is 25 per cent Charge; Rate of Charge at 3 AMP is 5 hours at 6 AMP is 2.5 hours at 10 AMP is 1.5 hours at 20 AMP is 45 minutes



BATTERY STATE OF CHARGE is 11.8 VDC is 0 per cent Charge; Rate of Charge at 3 AMP is 6 hours, 40 minutes at 6 AMP is 3 hours, 20 minutes at 10 AMP is 2 hours at 20 AMP is 1 hour



The figures listed above assume that the battery is charging at room temperature. If warmer than room temperature, use a slightly shorter charging time. If colder, use a slightly longer charging time.



The use of constant current chargers to charge maintenance free batteries is not recommended. Any overcharge will cause dry out and premature battery failure. If a constant current charger is the only type available, do not exceed the charge times listed above and do not continue charging the battery if it gets hot. When charging, never exceed 15 volts for more than 30 minutes.



If the battery gets hotter than 110 degrees F or 43 degrees C during charging, discontinue charger and allow the battery to cool. Overheating may result in plate distortion, internal shorting, dry out and/or other damage.

Try setting a lower spin speed. You may have a bulky load which the washer is having a difficult time getting up to the high speed spin you have selected. Also, did you know that on most LG washers, you can do just a spin without a rinse? Just turn the washer power on, then, without selecting a cycle, just push the spin speed selector to select the spin speed desired. This should set the cycle for about a 12 to 14 minutes pump and spin only. Then push start. You can spin that bulky load at the lowest spin, then try it again at the next faster spin if needed, without adding rinse water.

no solution here but i have same model number and am recycling it. everything works but chassis is loose from use of over 10 years. let me know if yoiu want me to send you controllers, timers, etc.
[email protected]

check the filter

Dont think so , clear drain @ sink you can use soda crystals drain pipe has debris in it...

It uses 1.2 gallons for each wash or rinse action in a cycle.  The water only runs until the 1.2 gallons amount is reached and then that water recycles through the pump for the duration of the action.  Start the dishwasher and time how long it takes until the water stops filling (not the entire time of the action).  Divide 1.2 by the number of minutes including seconds as a decimal fraction (i.e. 1 minute and 30 seconds = 1.5 minutes) to get the flow rate in gallons per minute (GPM).

sounds like adrain line issue, your creatring a syphoning effect . id assume thedrain line is either real low, perhaps running across thefloor or is screwed tightly to a longer hose ejecting through a wall with a full dry well

water usage is about right. top loaders use far more and so does hand washing
only way there would be excessive water usage is if machine were overfilling

Is the drain path free-flowing? That is, does the water eject freely during spin/rinse? Maybe there's a restriction in the line, or it's too high above the washer.